JVC HR-S9500EK setup guide Engage Insert Editing, Start Editing, END Insert Editing

Page 39

PLAY

		A
	INSERT	.
	INSERT	DUB
		DUB

1 2 3

2

4 5 6

7 8 9

0000	0	4
0000

1

PLAY

3

39

6	ENGAGE INSERT EDITING
	Press INSERT.

	● Your recorder enters the Insert-Pause mode. (" ", " "
	and " " light up on the front display panel.)
	● The TV screen changes from the still picture to the
	input source you are going to record.

START EDITING

7 Load the source cassette and play back the segment that is to be inserted. When you reach the start of the section of the source tape that you wish to insert, press PLAY to start the tape in your recorder; Insert Editing begins at this point.

●"" and "" are displayed on the front display panel.

END INSERT EDITING

8 At counter "0:00:00", Insert Editing will stop automati- cally while the tape continues running in the Play mode. If you wish to stop Insert Editing before the specified edit-out point, press 0000.

FOR AV INSERT EDITING

If you want to replace the picture, Hi-Fi audio soundtrack and

normal audio soundtrack all at the same time...

... In step 6 above, after you press INSERT, press A. DUB also. ("" and "" blink and "" lights up on the front display panel.)

NOTES:

●Suitable leads can be obtained from your dealer.

●Insert editing is not possible with cassettes whose safety tab has been removed.

●When insert editing is performed on a tape that has been recorded on another video recorder, the inserted portion may appear distorted.

●In insert editing, the recording speed (SP/LP) is determined by the previous recording to be replaced. If the previous recording's speed changes within a single edit, the inserted picture will be distorted at the switching point.

●A small portion of the recording which precedes an insert edit may become erased.

●Insert Editing is also possible using the rear panel AV1 IN/ OUT or AV2 IN connector. When using these connectors, make sure to select the correct input mode in step 2.

Image 39

Contents HR-S9500EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Mains outlet AV1 OUT switchTo connect to a TV with 21-pin AV input connector Scart Back of TVBack of TV Audio in connectors Mains outlet Mains Power CordBack of Recorder Before performing the following procedure, make sure that Will appear BeginningGo to item If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelStart Playback PlaybackLoad a Cassette PointActivate HIGH-SPEED Search PlaybackRecording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeCorrect number Video Plus+ Timer ProgrammingBefore performing Video Plus+ Timer Programming Press ProgPDC Recording Timer WarningTime Express Timer ProgrammingBefore performing Express Timer Programming Start TimeScreen SET PDC ModeTimer Mode Return to NormalCheck, Cancel And Replace Programmes VHS Super VHS and VHS Recording According To Tape TypePlayback/ Recording According To Tape Charac- teristics Turn on the RecorderS.T. Picture System During B.E.S.T RecordingPlayback Or press Record on the recorderDigital 3R Playback Picture AdjustmentManual Tracking Digital TBC/NRActivate Index Search Looking For Scene You WantSkip Over Unwanted SectionsNormal recorder Audio signal during TimeScanTimeScan Variable-Speed Search/ Reverse PlayForward Search Play Slow-Motion Still TimeScanTimeScan Audio Speed SP Speed LP Audio outputDuring Playback Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionActivate Spatializer Access Main MenuAdjust Audio Return to Normal ScreenRear panel AV1 OUT Switch SignalAutomatic Satellite Programme Recording Satellite Receiver UnitBefore performing the following steps Access Mode SET ScreenSelect AV2 Select Mode Engage Auto Satellite Prog REC ModeSET TV Brand Code TV Multi-brand Remote ControlControl Your TV Using Additional Buttons Remote Con- trol FunctionsOperate Satellite Receiver SET Remote Control CodeRE-SUPPLY Power SET Satellite Receiver Brand CodeEditing Mode Setting Minimizing Picture Degradation While EditingAdvantages Of S-VHS Video Recorders Edit From Camcorder Edit To Or From Another Video Recorder Quality S-VHS pictures AV2 Select SettingTV Receiver Your recorderStart Source Playback Access R.A. Edit ScreenPrepare for Editing Load Source CassetteEND R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point Start R.A. EditLocate END Point SET Input ModeReset the Counter Insert EditingEngage Insert Editing Start EditingEND Insert Editing Audio OUT Engage Audio DubbingStart Dubbing END Audio DubbingSET Jlip ID Number Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen Information On J TerminalOther Functions Access Main Menu ScreenAccess Mode SET Screen ENABLE/DISABLE ON-SCREEN DisplayAuto Timer Auto SP→LP TimerNext Function Memory Repeat PlaybackNtsc Playback RetakeAudio Cable not provided Speaker Connection To Stereo SystemSET Video Channel Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Tuner Set Perform Auto Channel SETAuto Channel Set Is displayed on the screen Screen preset positionsProcedures After Scan CompletedClose Confirmation Screen Storing Channels ManuallyEnter NEW Channel InformationChange Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Select Station Name Character Access Manual Channel SET ScreenSelect NEW Station Close ConfirmationStation Name TV Station And ID ListTV Station Channel Number Guide Just Clock Clock SetVideo Plus+ Setup NumberGuide Program Number Set Ä remain lit on the display panel. Is there Problem? Questions And AnswersTroubleshooting No power is applied to the recorderConnect the mains power cord Won’t stop Timer RecordingIndex Spatializer Button enables/disables Spatializer. pgRear View Audio OUT L/R Connectors enableRemote Control How To Use DA4 Double Azimuth helical Audio OUT x 1 S-Video connectors in x 1, OUT x