JVC HR-S9500EK Information On J Terminal, Terminal JLIPJoint Level Interface Protocol Connector

Page 41

Information On J Terminal

J terminal

	1	2	3
			2
NUMBER	4	5	6
NUMBER
	7	8	9
		0	4
	1

OK

MENU

ATTENTION

After you change your recorder's JLIP ID number, control signal transmission may not work properly. If this happens, turn off the recorder's power off once, then turn it back on and try again.

41

J Terminal (JLIP(Joint Level Interface Protocol) Connector)

The J Terminal is used to connect the recorder to a personal computer or similar device to allow computerized control of the recorder during editing and certain other operations.

Examples:

With the optional JLIP VIDEO CAPTURE BOX GV-CB3E:

●Enables Random Assemble Editing of up to 99 segments, using this recorder as the playback unit.

●Allows you to capture still images from the recorder into a personal computer.

For further details consult your nearest JVC dealer.

JLIP ID Number

Your recorder has its own JLIP ID number. This ID number must be unique when your recorder is connected to another device via its J terminal. The ID Number is preset to "1" at the factory. You can change this number to any number between "1" and "99". If it is necessary to change the JLIP ID number perform the following steps.

ACCESS MAIN MENU SCREEN

	1 Press MENU.
		ACCESS INITIAL SET SCREEN
		Press %Þ to move the highlight bar (pointer) to
	2 "INITIAL SET", then press OK or %.
		ACCESS JLIP ID NO. SET SCREEN
		Press %Þ and move the	INTIAL SET
		highlight bar (pointer) to	CLOCK SET
	3 "JLIP ID NO. SET", then		CLOCK SET
	3 "JLIP ID NO. SET", then		GUIDE PROG SET
		press OK or%.	JLIP ID NO. SET

			[5°] =
			[MENU] : EXIT

		SET JLIP ID NUMBER
		Press NUMBER keys to	JLIP ID NO. SET
		enter the desired ID
	4 number.
	4 number.			1
			CLOCK SET

			[0-9] =
			[MENU] : EXIT

		RETURN TO NORMAL SCREEN
	5 Press OK.

Image 41

Contents HR-S9500EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide To connect to a TV with 21-pin AV input connector Scart AV1 OUT switchBack of TV Mains outletBack of Recorder Back of TV Audio in connectorsMains outlet Mains Power Cord Go to item Before performing the following procedure, make sure thatWill appear Beginning If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelLoad a Cassette PlaybackPoint Start PlaybackActivate HIGH-SPEED Search PlaybackRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayBefore performing Video Plus+ Timer Programming Video Plus+ Timer ProgrammingPress Prog Correct numberPDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingStart Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes VHS Super VHS and VHS Recording According To Tape TypeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Playback RecordingOr press Record on the recorder During B.E.S.TManual Tracking Playback Picture AdjustmentDigital TBC/NR Digital 3RSkip Over Unwanted Looking For Scene You WantSections Activate Index SearchTimeScan Audio signal during TimeScanVariable-Speed Search/ Reverse Play Normal recorderTimeScan Audio TimeScanSpeed SP Speed LP Audio output Forward Search Play Slow-Motion StillReceiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection During PlaybackAdjust Audio Access Main MenuReturn to Normal Screen Activate SpatializerAutomatic Satellite Programme Recording Switch SignalSatellite Receiver Unit Rear panel AV1 OUTSelect AV2 Select Mode Access Mode SET ScreenEngage Auto Satellite Prog REC Mode Before performing the following stepsControl Your TV Using Additional Buttons TV Multi-brand Remote ControlRemote Con- trol Functions SET TV Brand CodeRE-SUPPLY Power SET Remote Control CodeSET Satellite Receiver Brand Code Operate Satellite ReceiverAdvantages Of S-VHS Video Recorders Editing Mode SettingMinimizing Picture Degradation While Editing Edit From Camcorder Edit To Or From Another Video Recorder TV Receiver AV2 Select SettingYour recorder Quality S-VHS picturesPrepare for Editing Access R.A. Edit ScreenLoad Source Cassette Start Source PlaybackLocate EDIT-OUT Point Locate EDIT-IN PointStart R.A. Edit END R.A. EditReset the Counter SET Input ModeInsert Editing Locate END PointEND Insert Editing Engage Insert EditingStart Editing Start Dubbing Engage Audio DubbingEND Audio Dubbing Audio OUTAccess Initial SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorInformation On J Terminal SET Jlip ID NumberAccess Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto Timer Auto SP→LP TimerNtsc Playback Repeat PlaybackRetake Next Function MemoryAudio Cable not provided Speaker Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Auto Channel Set Tuner SetPerform Auto Channel SET Procedures Screen preset positionsAfter Scan Completed Is displayed on the screenEnter NEW Channel Storing Channels ManuallyInformation Close Confirmation ScreenDelete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Select NEW Station Access Manual Channel SET ScreenClose Confirmation Select Station Name CharacterStation Name TV Station And ID ListTV Station Channel Number Guide Just Clock Clock SetGuide Program Number Set Video Plus+ SetupNumber Ä remain lit on the display panel. Is there Problem? Questions And AnswersConnect the mains power cord TroubleshootingNo power is applied to the recorder Won’t stop Timer RecordingIndex Spatializer Button enables/disables Spatializer. pgRear View Audio OUT L/R Connectors enableRemote Control How To Use DA4 Double Azimuth helical Audio OUT x 1 S-Video connectors in x 1, OUT x