JVC HR-S9500EK setup guide Timer Warning, PDC Recording

Page 15

 

SET TAPE SPEED

4 Press SP/LP ( ) to set the tape speed.

5

SET PDC MODE

Press PDC to select "ON" or "OFF".

If "VPS/PDC ON" is displayed on the screen or "VPS/

PDC" is lit on the display panel, PDC is set to ON.

 

If "VPS/PDC OFF" is displayed on the screen or "VPS/

 

PDC" is not lit on the display panel, PDC is set to OFF.

 

☞ "PDC Recording" in the column below.

 

● VPS (Video Programme System) recording is not

 

currently available in the U.K. and not possible with

 

this recorder.

 

RETURN TO NORMAL SCREEN

 

Press PROG or OK. "PROGRAM COMPLETED" appears

6 on the screen for about 5 seconds, then normal screen

15

Satellite Receiver Users

To timer-record a satellite broadcast using Video Plus+: 1 Set "AV2 SELECT" to the appropriate mode. ☞ pg. 35 2 Perform steps 1 – 7.

3 Set the satellite receiver to the appropriate channel before the selected programme begins.

4 Leave the satellite receiver's power on.

ATTENTION

Regarding Guide Program Number Set "GUIDE PROG SET" appears after performing step 3 if the Guide Program number for the PlusCode number you entered has not been set.

● Press the NUMBER keys or %Þ to input the preset position number on which your recorder receives that station, then press OK or %. The Video Plus+ Program screen appears.

 

appears.

 

 

 

● Repeat steps 1 – 6 for each additional programme.

 

 

 

ENGAGE RECORDER’S TIMER

7

MODE

Press ä(TIMER). The recorder turns off automatically

and äappears on the display panel.

 

● To disengage the timer, press ä (TIMER) again.

GUIDE PROG SET

GUIDE PROG

TV PROG

2

– –

[5°] =

 

[PROG] : EXIT

 

(Ex.) To timer-record a BBC2 programme with Video Plus+.

*If your recorder receives BBC2 on the preset position

2, press OK or %after entering "2".

NOTES:

● To Change The Stop Time . . .

. . . press STOP +/– after pressing OK in step 3. You can

compensate for anticipated programme schedule delays this

way.

● To Timer-Record Weekly Or Daily Serials . . .

. . . after pressing OK in step 3, press WEEKLY (NUMBER key

“9”) for weekly serials or DAILY (NUMBER key “8”) for daily

Timer Warning

If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on the screen to tell you that the recording is due to start in 5 minutes.

–WARNING– TIMER RECORDING

TO START SOON

[]

serials (Monday – Friday). Either "WEEKLY" or "DAILY"

appears on the screen. Pressing the button again makes the

corresponding indication disappear.

● You can programme this recorder to timer-record as many as 8

programmes. If you try to programme the recorder to record a

ninth, "PROGRAM FULL" appears on screen and "FULL"

appears on the front display panel. To record the extra

programme, you must first cancel any unnecessary

programmes (☞ pg. 18).

● It is not possible to timer-record a TV programme with a

PlusCode number which starts with "0".

NOTES:

●The warning only appears if you’re not in the Timer mode at the time.

●If this recorder is being used as the player for tape dubbing, the warning screen will be recorded on the tape in the other video recorder.

The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press .

PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times which you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service only in a very few areas. All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the channel you intend to record does not offer a PDC service your recorder will not start recording if PDC has been selected. Be sure to set PDC to "OFF" if PDC is not available on your selected channel (☞ step 5 above).

NOTES:

●PDC recording is also possible when a satellite receiver or a cable system is connected to AV2 IN on your recorder.

●PDC recording is also possible via the AV1 IN/OUT connector.

Page 14 Page 16
Image 15
Page 14 Page 16
Contents HR-S9500EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Mains outlet AV1 OUT switchTo connect to a TV with 21-pin AV input connector Scart Back of TVBack of TV Audio in connectors Mains outlet Mains Power CordBack of Recorder Before performing the following procedure, make sure that Will appear BeginningGo to item If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelStart Playback PlaybackLoad a Cassette PointActivate HIGH-SPEED Search PlaybackRecording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeCorrect number Video Plus+ Timer ProgrammingBefore performing Video Plus+ Timer Programming Press ProgPDC Recording Timer WarningTime Express Timer ProgrammingBefore performing Express Timer Programming Start TimeScreen SET PDC ModeTimer Mode Return to NormalCheck, Cancel And Replace Programmes VHS Super VHS and VHS Recording According To Tape TypePlayback/ Recording According To Tape Charac- teristics Turn on the RecorderS.T. Picture System During B.E.S.T RecordingPlayback Or press Record on the recorderDigital 3R Playback Picture AdjustmentManual Tracking Digital TBC/NRActivate Index Search Looking For Scene You WantSkip Over Unwanted SectionsNormal recorder Audio signal during TimeScanTimeScan Variable-Speed Search/ Reverse PlayForward Search Play Slow-Motion Still TimeScanTimeScan Audio Speed SP Speed LP Audio outputDuring Playback Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionActivate Spatializer Access Main MenuAdjust Audio Return to Normal ScreenRear panel AV1 OUT Switch SignalAutomatic Satellite Programme Recording Satellite Receiver UnitBefore performing the following steps Access Mode SET ScreenSelect AV2 Select Mode Engage Auto Satellite Prog REC ModeSET TV Brand Code TV Multi-brand Remote ControlControl Your TV Using Additional Buttons Remote Con- trol FunctionsOperate Satellite Receiver SET Remote Control CodeRE-SUPPLY Power SET Satellite Receiver Brand CodeEditing Mode Setting Minimizing Picture Degradation While EditingAdvantages Of S-VHS Video Recorders Edit From Camcorder Edit To Or From Another Video Recorder Quality S-VHS pictures AV2 Select SettingTV Receiver Your recorderStart Source Playback Access R.A. Edit ScreenPrepare for Editing Load Source CassetteEND R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point Start R.A. EditLocate END Point SET Input ModeReset the Counter Insert EditingEngage Insert Editing Start EditingEND Insert Editing Audio OUT Engage Audio DubbingStart Dubbing END Audio DubbingSET Jlip ID Number Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen Information On J TerminalOther Functions Access Main Menu ScreenAccess Mode SET Screen ENABLE/DISABLE ON-SCREEN DisplayAuto Timer Auto SP→LP TimerNext Function Memory Repeat PlaybackNtsc Playback RetakeAudio Cable not provided Speaker Connection To Stereo SystemSET Video Channel Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Tuner Set Perform Auto Channel SETAuto Channel Set Is displayed on the screen Screen preset positionsProcedures After Scan CompletedClose Confirmation Screen Storing Channels ManuallyEnter NEW Channel InformationChange Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Select Station Name Character Access Manual Channel SET ScreenSelect NEW Station Close ConfirmationStation Name TV Station And ID ListTV Station Channel Number Guide Just Clock Clock SetVideo Plus+ Setup NumberGuide Program Number Set Ä remain lit on the display panel. Is there Problem? Questions And AnswersTroubleshooting No power is applied to the recorderConnect the mains power cord Won’t stop Timer RecordingIndex Spatializer Button enables/disables Spatializer. pgRear View Audio OUT L/R Connectors enableRemote Control How To Use DA4 Double Azimuth helical Audio OUT x 1 S-Video connectors in x 1, OUT x
Top Page Image Contents