JVC HR-S9500EK SET Remote Control Code, RE-SUPPLY Power, SET Satellite Receiver Brand Code

Page 31

VCR/TV/SAT

NUMBER "1"

 

1

2

3

 

 

 

 

 

 

2

NUMBER

 

 

4

5

6

 

 

 

 

 

 

 

"2"

8

9

 

 

 

NUMBER

7

 

 

 

 

0

 

4

 

 

 

 

 

 

1

STOP

TV PROG+/–

3

A/B

Remote A/B Code Switching

The remote control is capable of controlling two JVC video recorders independently; one set to respond to the remote control’s A code control signals and another set to respond to B code control signals. The remote control is preset to send A code signals because your video recorder is initially set to respond to A code signals. You can easily modify your video recorder to respond to B code signals.

REMOVE POWER SUPPLY

1 Unplug the mains power cord from the mains outlet.

SET REMOTE CONTROL

CODE

2 While holding down A/B on the remote control, press the NUMBER key "2" and then press STOP.

RE-SUPPLY POWER

3 Plug the mains power cord back into the mains outlet.

TURN THE RECORDER ON

4 Press on the remote control. The recorder will now only respond to B code signals.

NOTE:

To set the recorder back to respond to A code signals, repeat the same procedure as shown above except pressing NUMBER key "1" instead of "2" in step 2.

31

Satellite Receiver Multi-

Brand Remote Control

Your remote control can operate the basic functions of your satellite receiver set. In addition to JVC satellite receivers, other manufacturer’s satellite receivers can also be controlled.

Before you start . . .

Turn on the satellite receiver using its remote control.

Set the remote control’s VCR/TV/SAT switch to SAT.

SET SATELLITE RECEIVER

BRAND CODE

Refer to the chart below. While holding down

 

 

 

on the

 

recorder's remote control, enter your satellite receiver’s

1 brand code using the NUMBER keys, then press STOP.

Check if the satellite receiver's power goes off as it

should. If it does, try other operations (step 2).

 

Once you have set the remote control to operate the satellite receiver, you don't have to repeat this step until you replace your remote control's battteries.

Some satellite receiver brands have more than one code. If the satellite receiver does not function with one code, try entering another.

OPERATE SATELLITE

RECEIVER

2

Press the corresponding button: , TV PROG +/–,

NUMBER keys.

For VIDEOWAY or some brands of satellite receiver, you

must press after having pressed the NUMBER keys.

The NUMBER buttons may not function with some satellite receivers.

To return the remote to video recorder control, set the VCR/TV/SAT switch to VCR.

IMPORTANT

Although the provided remote control unit is compatible with JVC satellite receivers, as well as many other models, it may not work with your satellite receiver, or in some instances, may have limited function capability.

SATELLITE RECEIVER BRAND

CODE

JVC

72, 73

AMSTRAD

60, 61, 62, 63

BT

72

CANAL +

81

FINLUX

68

GRUNDIG

64, 65

HIRSCHMANN

64

ITT

68

JERROLD

75

KATHREIN

70, 71

LUXOR

68

MASPRO

70

NOKIA

68

PACE

65, 67

PANASONIC

74

PHILIPS

66

RFT

69

SALORA

68

SIEMENS

64

SKYMASTER

69

VIDEOWAY

76

WISI

64

 

 

Image 31
Contents HR-S9500EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Mains outlet AV1 OUT switchTo connect to a TV with 21-pin AV input connector Scart Back of TVMains outlet Mains Power Cord Back of TV Audio in connectorsBack of Recorder Will appear Beginning Before performing the following procedure, make sure thatGo to item If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelStart Playback PlaybackLoad a Cassette PointActivate HIGH-SPEED Search PlaybackRecording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeCorrect number Video Plus+ Timer ProgrammingBefore performing Video Plus+ Timer Programming Press ProgPDC Recording Timer WarningTime Express Timer ProgrammingBefore performing Express Timer Programming Start TimeScreen SET PDC ModeTimer Mode Return to NormalCheck, Cancel And Replace Programmes VHS Super VHS and VHS Recording According To Tape TypeTurn on the Recorder Playback/ Recording According To Tape Charac- teristicsS.T. Picture System During B.E.S.T RecordingPlayback Or press Record on the recorderDigital 3R Playback Picture AdjustmentManual Tracking Digital TBC/NRActivate Index Search Looking For Scene You WantSkip Over Unwanted SectionsNormal recorder Audio signal during TimeScanTimeScan Variable-Speed Search/ Reverse PlayForward Search Play Slow-Motion Still TimeScanTimeScan Audio Speed SP Speed LP Audio outputDuring Playback Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionActivate Spatializer Access Main MenuAdjust Audio Return to Normal ScreenRear panel AV1 OUT Switch SignalAutomatic Satellite Programme Recording Satellite Receiver UnitBefore performing the following steps Access Mode SET ScreenSelect AV2 Select Mode Engage Auto Satellite Prog REC ModeSET TV Brand Code TV Multi-brand Remote ControlControl Your TV Using Additional Buttons Remote Con- trol FunctionsOperate Satellite Receiver SET Remote Control CodeRE-SUPPLY Power SET Satellite Receiver Brand CodeMinimizing Picture Degradation While Editing Editing Mode SettingAdvantages Of S-VHS Video Recorders Edit From Camcorder Edit To Or From Another Video Recorder Quality S-VHS pictures AV2 Select SettingTV Receiver Your recorderStart Source Playback Access R.A. Edit ScreenPrepare for Editing Load Source CassetteEND R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point Start R.A. EditLocate END Point SET Input ModeReset the Counter Insert EditingStart Editing Engage Insert EditingEND Insert Editing Audio OUT Engage Audio DubbingStart Dubbing END Audio DubbingSET Jlip ID Number Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen Information On J TerminalOther Functions Access Main Menu ScreenAccess Mode SET Screen ENABLE/DISABLE ON-SCREEN DisplayAuto Timer Auto SP→LP TimerNext Function Memory Repeat PlaybackNtsc Playback RetakeAudio Cable not provided Speaker Connection To Stereo SystemSET Video Channel Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Perform Auto Channel SET Tuner SetAuto Channel Set Is displayed on the screen Screen preset positionsProcedures After Scan CompletedClose Confirmation Screen Storing Channels ManuallyEnter NEW Channel InformationFine-Tuning Channels Already Stored Change Station Preset PositionDelete a Channel Select Station Name Character Access Manual Channel SET ScreenSelect NEW Station Close ConfirmationStation Name TV Station And ID ListTV Station Channel Number Guide Just Clock Clock SetNumber Video Plus+ SetupGuide Program Number Set Ä remain lit on the display panel. Is there Problem? Questions And AnswersNo power is applied to the recorder TroubleshootingConnect the mains power cord Won’t stop Timer RecordingIndex Spatializer Button enables/disables Spatializer. pgRear View Audio OUT L/R Connectors enableRemote Control How To Use DA4 Double Azimuth helical Audio OUT x 1 S-Video connectors in x 1, OUT x