JVC HR-S9500EK setup guide Back of TV, Mains outlet, AV1 OUT switch

Page 6

6

QUICKSETUPGUIDE(cont.)

STEP

2

INSTALLATION

CONNECT VIDEO RECORDER TO TV

Place the recorder on a stable, flat surface.

Back of TV

Aerial connector

21-pin AV input connector (SCART)

RF Cable (provided)

21-pin SCART Cable (not provided)

Make this connection if your TV has a

21-pin AV input connector (SCART) in order to reduce the possibility of interference. And if you are using a stereo TV, you will need this cable in order to enjoy stereo playback of videotapes.

TV Aerial Cable (not provided)

Mains Power Cord

 

AV1 OUT

S OUT

AV1 IN/OUT

COMP. Y/C

AV2 IN

Mains outlet

ANT. IN

RL

AUDIO OUT

JLIP

RF OUT

PAUSE/

R.A. EDIT

AV1 OUT switch

Back of Recorder

RF CONNECTION

To connect to a TV with NO 21-pin AV input connector (SCART) . . .

1– Disconnect the TV aerial cable from the TV.

2– Connect the TV aerial cable to the ANT. IN jack on the rear panel of the recorder.

3– Connect the provided RF cable between the RF OUT jack on the rear panel of the recorder and the TV’s aerial connector.

AV CONNECTION

To connect to a TV with 21-pin AV input connector (SCART) . . .

1– Connect the aerial, recorder and TV as per “RF CONNECTION”. 2– Connect an optional SCART cable between the AV1 IN/OUT socket on the rear panel of the recorder and the TV’s 21-pin

AV input connector (SCART).

3– Set the AV1 OUT switch to the appropriate position. See "AV1

OUTPUT SIGNAL SELECTION FOR AV CONNECTION" below.

AV1 OUTPUT SIGNAL SELECTION FOR AV CONNECTION

The AV1 IN/OUT connector accepts only a composite signal (regular video signal), but can deliver either a composite video signal or a Y/C signal (a signal in which the luminance and chrominance signals are separated) according to the setting of the rear panel AV1 OUT switch.

●If your TV's 21-pin AV input connector (SCART) is compatible only with the regular video signal, set this switch to COMP.

●If your TV's 21-pin AV input connector (SCART) is compatible with the Y/C signal, set this switch to Y/C. You can obtain high- quality S-VHS pictures. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

NOTES:

●Set your TV to the VIDEO (or AV), Y/C, or RGB mode according to the type of your TV's SCART connector.

●For switching the TV's mode, refer to the instruction manual of your television.

●To obtain high-quality S-VHS pictures, you can also use the S-VIDEO CONNECTION described on page 7.

ATTENTION

■Do NOT Plug the mains power cord into a mains outlet until all connections are completed.

■Do NOT press the button on the recorder or on the remote control to turn on the recorder's power before you start the Auto Set Up procedure described on page 8.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents HR-S9500EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV AV1 OUT switchTo connect to a TV with 21-pin AV input connector Scart Mains outletBack of TV Audio in connectors Mains outlet Mains Power CordBack of Recorder Before performing the following procedure, make sure that Will appear BeginningGo to item Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPoint PlaybackLoad a Cassette Start PlaybackPlayback Activate HIGH-SPEED SearchRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayPress Prog Video Plus+ Timer ProgrammingBefore performing Video Plus+ Timer Programming Correct numberTimer Warning PDC RecordingStart Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode ScreenCheck, Cancel And Replace Programmes Recording According To Tape Type VHS Super VHS and VHSPlayback/ Recording According To Tape Charac- teristics Turn on the RecorderS.T. Picture System Or press Record on the recorder RecordingPlayback During B.E.S.TDigital TBC/NR Playback Picture AdjustmentManual Tracking Digital 3RSections Looking For Scene You WantSkip Over Unwanted Activate Index SearchVariable-Speed Search/ Reverse Play Audio signal during TimeScanTimeScan Normal recorderSpeed SP Speed LP Audio output TimeScanTimeScan Audio Forward Search Play Slow-Motion StillSoundtrack Selection Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes During PlaybackReturn to Normal Screen Access Main MenuAdjust Audio Activate SpatializerSatellite Receiver Unit Switch SignalAutomatic Satellite Programme Recording Rear panel AV1 OUTEngage Auto Satellite Prog REC Mode Access Mode SET ScreenSelect AV2 Select Mode Before performing the following stepsRemote Con- trol Functions TV Multi-brand Remote ControlControl Your TV Using Additional Buttons SET TV Brand CodeSET Satellite Receiver Brand Code SET Remote Control CodeRE-SUPPLY Power Operate Satellite ReceiverEditing Mode Setting Minimizing Picture Degradation While EditingAdvantages Of S-VHS Video Recorders Edit From Camcorder Edit To Or From Another Video Recorder Your recorder AV2 Select SettingTV Receiver Quality S-VHS picturesLoad Source Cassette Access R.A. Edit ScreenPrepare for Editing Start Source PlaybackStart R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point END R.A. EditInsert Editing SET Input ModeReset the Counter Locate END PointEngage Insert Editing Start EditingEND Insert Editing END Audio Dubbing Engage Audio DubbingStart Dubbing Audio OUTInformation On J Terminal Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen SET Jlip ID NumberENABLE/DISABLE ON-SCREEN Display Access Main Menu ScreenAccess Mode SET Screen Other FunctionsAuto SP→LP Timer Auto TimerRetake Repeat PlaybackNtsc Playback Next Function MemoryConnection To Stereo System Audio Cable not provided SpeakerVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelWith RF Connection Tuner Set Perform Auto Channel SETAuto Channel Set After Scan Completed Screen preset positionsProcedures Is displayed on the screenInformation Storing Channels ManuallyEnter NEW Channel Close Confirmation ScreenChange Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Close Confirmation Access Manual Channel SET ScreenSelect NEW Station Select Station Name CharacterTV Station And ID List Station NameTV Station Channel Number Guide Clock Set Just ClockVideo Plus+ Setup NumberGuide Program Number Set Questions And Answers Ä remain lit on the display panel. Is there Problem?Troubleshooting No power is applied to the recorderConnect the mains power cord Timer Recording Won’t stopSpatializer Button enables/disables Spatializer. pg IndexAudio OUT L/R Connectors enable Rear ViewRemote Control How To Use Audio OUT x 1 S-Video connectors in x 1, OUT x DA4 Double Azimuth helical
Top Page Image Contents