JVC HR-S9500EK setup guide With RF Connection

Page 47

STOP

1 2 3

2

4 5 6

7 8 9

0

4

TV PROG

1

OK

TEST SIGNAL

The channel on which the screen on the left appears clearly in step 2 is your Video Channel.

47

With RF Connection

Before performing the following procedure, make sure that:

■the mains power cord is plugged into the mains outlet.

■the video recorder is turned off and there is no cassette inserted in the recorder.

■the connected TV is turned on.

■batteries have been installed in the remote control.

ACCESS VIDEO CHANNEL

SET MODE

1 Press and hold down STOP on the recorder until the display panel shows the following.

SET VIDEO CHANNEL

2 Press TV PROG+ or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area. Refer to list on page 54 for details of broadcast stations in your area.

(Ex.) If channel 36 is available in your area

Then set your TV to UHF channel 36. (Refer to the instructions supplied with your TV set for how to do this.)

●If the two vertical white bars appear clearly on the screen as shown in the illustration at buttom left, go to step 3.

●If the two vertical white bars do not appear clearly, re- set the video recorder to another vacant channel and try again.

IMPORTANT

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

EXIT VIDEO CHANNEL SET

MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to the Video Channel.

Image 47

Contents HR-S9500EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Mains outlet AV1 OUT switchTo connect to a TV with 21-pin AV input connector Scart Back of TVBack of Recorder Back of TV Audio in connectorsMains outlet Mains Power Cord Go to item Before performing the following procedure, make sure thatWill appear Beginning If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelStart Playback PlaybackLoad a Cassette PointActivate HIGH-SPEED Search PlaybackRecording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeCorrect number Video Plus+ Timer ProgrammingBefore performing Video Plus+ Timer Programming Press ProgPDC Recording Timer WarningTime Express Timer ProgrammingBefore performing Express Timer Programming Start TimeScreen SET PDC ModeTimer Mode Return to NormalCheck, Cancel And Replace Programmes VHS Super VHS and VHS Recording According To Tape TypeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder During B.E.S.T RecordingPlayback Or press Record on the recorderDigital 3R Playback Picture AdjustmentManual Tracking Digital TBC/NRActivate Index Search Looking For Scene You WantSkip Over Unwanted SectionsNormal recorder Audio signal during TimeScanTimeScan Variable-Speed Search/ Reverse PlayForward Search Play Slow-Motion Still TimeScanTimeScan Audio Speed SP Speed LP Audio outputDuring Playback Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionActivate Spatializer Access Main MenuAdjust Audio Return to Normal ScreenRear panel AV1 OUT Switch SignalAutomatic Satellite Programme Recording Satellite Receiver UnitBefore performing the following steps Access Mode SET ScreenSelect AV2 Select Mode Engage Auto Satellite Prog REC ModeSET TV Brand Code TV Multi-brand Remote ControlControl Your TV Using Additional Buttons Remote Con- trol FunctionsOperate Satellite Receiver SET Remote Control CodeRE-SUPPLY Power SET Satellite Receiver Brand CodeAdvantages Of S-VHS Video Recorders Editing Mode SettingMinimizing Picture Degradation While Editing Edit From Camcorder Edit To Or From Another Video Recorder Quality S-VHS pictures AV2 Select SettingTV Receiver Your recorderStart Source Playback Access R.A. Edit ScreenPrepare for Editing Load Source CassetteEND R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point Start R.A. EditLocate END Point SET Input ModeReset the Counter Insert EditingEND Insert Editing Engage Insert EditingStart Editing Audio OUT Engage Audio DubbingStart Dubbing END Audio DubbingSET Jlip ID Number Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen Information On J TerminalOther Functions Access Main Menu ScreenAccess Mode SET Screen ENABLE/DISABLE ON-SCREEN DisplayAuto Timer Auto SP→LP TimerNext Function Memory Repeat PlaybackNtsc Playback RetakeAudio Cable not provided Speaker Connection To Stereo SystemSET Video Channel Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Auto Channel Set Tuner SetPerform Auto Channel SET Is displayed on the screen Screen preset positionsProcedures After Scan CompletedClose Confirmation Screen Storing Channels ManuallyEnter NEW Channel InformationDelete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Select Station Name Character Access Manual Channel SET ScreenSelect NEW Station Close ConfirmationStation Name TV Station And ID ListTV Station Channel Number Guide Just Clock Clock SetGuide Program Number Set Video Plus+ SetupNumber Ä remain lit on the display panel. Is there Problem? Questions And AnswersConnect the mains power cord TroubleshootingNo power is applied to the recorder Won’t stop Timer RecordingIndex Spatializer Button enables/disables Spatializer. pgRear View Audio OUT L/R Connectors enableRemote Control How To Use DA4 Double Azimuth helical Audio OUT x 1 S-Video connectors in x 1, OUT x