JVC HR-S9500EK setup guide Engage Audio Dubbing, Start Dubbing, END Audio Dubbing, Audio OUT

Page 40

40

ADVANCEDOPERATIONS (cont.)

Audio dubbing replaces the normal audio sound of a previously

Audio Dubbing recorded tape with a new soundtrack.

 

Normal audio track

Pre-recorded tape

STOP

PROG

PLAY

 

TV

 

Video/Hi-Fi audio track

Audio-dubbed tape

PAUSE

CD Player etc.

 

CD Player etc.

Mixer

Audio mixer

output

 

 

Original sound

 

AUDIO OUT

NOTES:

● When monitoring the sound during Audio Dubbing, the normal soundtrack is automatically selected. If you wish to hear the mixed sound (Hi-Fi + Normal soundtracks), press AUDIO on the remote control to select " + (L+R)+NORM" (☞ pg. 26).

● Audio dubbing stops automatically when the counter reaches "0:00:00", and the recorder enters the Play mode. Check the counter reading before dubbing.

● Audio dubbing is also possible using the rear panel AV1 IN/OUT or AV2 IN connector. When using these connectors, make sure to select the correct input mode in step 2.

● Audio dubbing cannot be performed on a cassette that has had its record safety tab removed.

● When playing back an audio-dubbed tape, press AUDIO on the remote control to select the soundtrack you wish to hear (☞ pg. 26).

1

2

3

4

5

6

MAKE CONNECTIONS

Connect an audio component to the AUDIO L + R connectors on the recorder's front panel.

●When connecting monaural equipment, use only the recorder's AUDIO L connector.

SET INPUT MODE

Press NUMBER key "0" and/or TV PROG so that "F-1" or "S-1" appears in place of a channel number.

LOCATE START POINT

Press PLAY to start playback of the tape in your recorder, and press PAUSE when you find the point where you want to start dubbing.

ENGAGE AUDIO DUBBING

Press A. DUB.

●It is possible to take the original sound recorded on the tape in your recorder and mix it with other sounds from a microphone, CD player etc. To perform this audio dubbing with audio mixing, connect as in the diagram on the left.

●Your recorder enters the Audio Dubbing Pause mode. ("" blinks, "" and "" light up on the front display panel.)

●To perform audio dubbing with audio mixing, press

AUDIO on the remote control to select " + (L+R)" at this point.

*Audio dubbing with audio mixing is not possible if you're using a monaural audio component, or if you don't have an audio mixer.

START DUBBING

Engage the audio component's Play mode, then press PLAY to start the tape in your recorder. Audio dubbing begins at this point.

●"" blinks and "" is displayed on the front display panel.

●To stop dubbing temporarily, press PAUSE. Press PLAY to resume dubbing.

END AUDIO DUBBING

Press STOP to stop the tape in your recorder, and engage the audio component's Stop mode.

Page 39 Page 41
Image 40
Page 39 Page 41
Contents HR-S9500EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide AV1 OUT switch To connect to a TV with 21-pin AV input connector ScartBack of TV Mains outletMains outlet Mains Power Cord Back of TV Audio in connectorsBack of Recorder Will appear Beginning Before performing the following procedure, make sure thatGo to item Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPlayback Load a CassettePoint Start PlaybackPlayback Activate HIGH-SPEED SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Before performing Video Plus+ Timer ProgrammingPress Prog Correct numberTimer Warning PDC RecordingExpress Timer Programming Before performing Express Timer ProgrammingStart Time TimeSET PDC Mode Timer ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes Recording According To Tape Type VHS Super VHS and VHSTurn on the Recorder Playback/ Recording According To Tape Charac- teristicsS.T. Picture System Recording PlaybackOr press Record on the recorder During B.E.S.TPlayback Picture Adjustment Manual TrackingDigital TBC/NR Digital 3RLooking For Scene You Want Skip Over UnwantedSections Activate Index SearchAudio signal during TimeScan TimeScanVariable-Speed Search/ Reverse Play Normal recorderTimeScan TimeScan AudioSpeed SP Speed LP Audio output Forward Search Play Slow-Motion StillSelecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackAccess Main Menu Adjust AudioReturn to Normal Screen Activate SpatializerSwitch Signal Automatic Satellite Programme RecordingSatellite Receiver Unit Rear panel AV1 OUTAccess Mode SET Screen Select AV2 Select ModeEngage Auto Satellite Prog REC Mode Before performing the following stepsTV Multi-brand Remote Control Control Your TV Using Additional ButtonsRemote Con- trol Functions SET TV Brand CodeSET Remote Control Code RE-SUPPLY PowerSET Satellite Receiver Brand Code Operate Satellite ReceiverMinimizing Picture Degradation While Editing Editing Mode SettingAdvantages Of S-VHS Video Recorders Edit From Camcorder Edit To Or From Another Video Recorder AV2 Select Setting TV ReceiverYour recorder Quality S-VHS picturesAccess R.A. Edit Screen Prepare for EditingLoad Source Cassette Start Source PlaybackLocate EDIT-IN Point Locate EDIT-OUT PointStart R.A. Edit END R.A. EditSET Input Mode Reset the CounterInsert Editing Locate END PointStart Editing Engage Insert EditingEND Insert Editing Engage Audio Dubbing Start DubbingEND Audio Dubbing Audio OUTTerminal JLIPJoint Level Interface Protocol Connector Access Initial SET ScreenInformation On J Terminal SET Jlip ID NumberAccess Main Menu Screen Access Mode SET ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto SP→LP Timer Auto TimerRepeat Playback Ntsc PlaybackRetake Next Function MemoryConnection To Stereo System Audio Cable not provided SpeakerAccess Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Perform Auto Channel SET Tuner SetAuto Channel Set Screen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Enter NEW ChannelInformation Close Confirmation ScreenFine-Tuning Channels Already Stored Change Station Preset PositionDelete a Channel Access Manual Channel SET Screen Select NEW StationClose Confirmation Select Station Name CharacterTV Station And ID List Station NameTV Station Channel Number Guide Clock Set Just ClockNumber Video Plus+ SetupGuide Program Number Set Questions And Answers Ä remain lit on the display panel. Is there Problem?No power is applied to the recorder TroubleshootingConnect the mains power cord Timer Recording Won’t stopSpatializer Button enables/disables Spatializer. pg IndexAudio OUT L/R Connectors enable Rear ViewRemote Control How To Use Audio OUT x 1 S-Video connectors in x 1, OUT x DA4 Double Azimuth helical
Top Page Image Contents