JVC HR-S9500EK setup guide Video Channel Set, Access Video Channel SET Mode, SET Video Channel

Page 46

46SUBSIDIARYSETTINGS

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

STOP

IMPORTANT

Perform the following steps only if —

—Video Channel Set has not been done correctly by the Auto Set Up function (☞ pg. 8).

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV or S-VIDEO connection, or vice versa.

●If you have connected the video recorder to your TV via both the provided RF cable and a

21-pin SCART cable (AV connection), or via the provided RF cable, the provided S-Video cable and an audio cable (S-VIDEO connection), you do not need the video channel so you have to set the video channel to off. — Go to "With AV or S- VIDEO Connection" below.

●If you have connected the video recorder to your TV via the provided RF cable only (RF connection), you have to set the correct video channel — Go to "With RF Connection" on page 47.

1 2 3

2

4 5 6

7 8 9

0

4

TV PROG

1

OK

With AV or S-VIDEO

Connection

Before performing the following procedure, make sure that:

■the mains power cord is plugged into the mains outlet.

■the video recorder is turned off and there is no cassette inserted in the recorder.

■batteries have been installed in the remote control.

ACCESS VIDEO CHANNEL SET MODE

	Press and hold down STOP on the recorder until the
1		display panel shows the following.
1

2	SET VIDEO CHANNEL
	Press TV PROG – until the display panel shows
		"–OUT– –".

●Now the video channel is set to off.

EXIT VIDEO CHANNEL SET MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to its AV mode. Refer to the instructions supplied with your TV set for how to do this.

Image 46

Contents HR-S9500EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV AV1 OUT switchTo connect to a TV with 21-pin AV input connector Scart Mains outletMains outlet Mains Power Cord Back of TV Audio in connectorsBack of Recorder Will appear Beginning Before performing the following procedure, make sure thatGo to item Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPoint PlaybackLoad a Cassette Start PlaybackPlayback Activate HIGH-SPEED SearchRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayPress Prog Video Plus+ Timer ProgrammingBefore performing Video Plus+ Timer Programming Correct numberTimer Warning PDC RecordingStart Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode ScreenCheck, Cancel And Replace Programmes Recording According To Tape Type VHS Super VHS and VHSTurn on the Recorder Playback/ Recording According To Tape Charac- teristicsS.T. Picture System Or press Record on the recorder RecordingPlayback During B.E.S.TDigital TBC/NR Playback Picture AdjustmentManual Tracking Digital 3RSections Looking For Scene You WantSkip Over Unwanted Activate Index SearchVariable-Speed Search/ Reverse Play Audio signal during TimeScanTimeScan Normal recorderSpeed SP Speed LP Audio output TimeScanTimeScan Audio Forward Search Play Slow-Motion StillSoundtrack Selection Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes During PlaybackReturn to Normal Screen Access Main MenuAdjust Audio Activate SpatializerSatellite Receiver Unit Switch SignalAutomatic Satellite Programme Recording Rear panel AV1 OUTEngage Auto Satellite Prog REC Mode Access Mode SET ScreenSelect AV2 Select Mode Before performing the following stepsRemote Con- trol Functions TV Multi-brand Remote ControlControl Your TV Using Additional Buttons SET TV Brand CodeSET Satellite Receiver Brand Code SET Remote Control CodeRE-SUPPLY Power Operate Satellite ReceiverMinimizing Picture Degradation While Editing Editing Mode SettingAdvantages Of S-VHS Video Recorders Edit From Camcorder Edit To Or From Another Video Recorder Your recorder AV2 Select SettingTV Receiver Quality S-VHS picturesLoad Source Cassette Access R.A. Edit ScreenPrepare for Editing Start Source PlaybackStart R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point END R.A. EditInsert Editing SET Input ModeReset the Counter Locate END PointStart Editing Engage Insert EditingEND Insert Editing END Audio Dubbing Engage Audio DubbingStart Dubbing Audio OUTInformation On J Terminal Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen SET Jlip ID NumberENABLE/DISABLE ON-SCREEN Display Access Main Menu ScreenAccess Mode SET Screen Other FunctionsAuto SP→LP Timer Auto TimerRetake Repeat PlaybackNtsc Playback Next Function MemoryConnection To Stereo System Audio Cable not provided SpeakerVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelWith RF Connection Perform Auto Channel SET Tuner SetAuto Channel Set After Scan Completed Screen preset positionsProcedures Is displayed on the screenInformation Storing Channels ManuallyEnter NEW Channel Close Confirmation ScreenFine-Tuning Channels Already Stored Change Station Preset PositionDelete a Channel Close Confirmation Access Manual Channel SET ScreenSelect NEW Station Select Station Name CharacterTV Station And ID List Station NameTV Station Channel Number Guide Clock Set Just ClockNumber Video Plus+ SetupGuide Program Number Set Questions And Answers Ä remain lit on the display panel. Is there Problem?No power is applied to the recorder TroubleshootingConnect the mains power cord Timer Recording Won’t stopSpatializer Button enables/disables Spatializer. pg IndexAudio OUT L/R Connectors enable Rear ViewRemote Control How To Use Audio OUT x 1 S-Video connectors in x 1, OUT x DA4 Double Azimuth helical