JVC 0105KTH-MW-BJ, LPT1016-001A manual Timer Recording VHS deck, Timer recording won’t work

Page 69

EN 69

TIMER RECORDING (VHS deck)

Timer recording won’t work.

The clock and/or the timer have been set incorrectly. ]Re-perform the clock and/or timer settings.

The timer is not engaged.

]Press # and confirm that “#” is displayed on the front display panel.

Timer programming is not possible.

Timer recording is in progress.

]Timer programming can’t be performed while a timer recording is in progress. Wait until it finishes.

” on the front display panel won’t stop blinking.

The timer is engaged but there’s no cassette loaded. ]Load a cassette with the record safety tab intact.

”, “ ” and “” on the front display panel won’t stop blinking.

The loaded cassette has had its record safety tab removed. ]Remove the cassette and cover the hole with adhesive tape, or

insert a cassette with the record safety tab intact.

The end of the tape was reached during timer recording.

]The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

]Turn off the timer mode by pressing timer button or next operations cannot be carried on.

” blinks for 10 seconds and the Timer mode is disengaged.

# has been pressed when there are no programs in memory, or the timer record information has been programmed

incorrectly.

]Check the programmed data and re-program as necessary, then press # again.

The SHOWVIEW system does not timer-record properly.

The unit’s channel positions have been set incorrectly.

]Refer to “G-CODE®/SHOWVIEWTMTimer Programming” ( pg. 27) and re-perform the procedure.

” and “” on the front display panel won’t stop blinking.

The end of the tape was reached during Instant Timer

Recording.

]The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

”, “” and “” on the front display panel won’t stop blinking.

The loaded cassette has had its record safety tab removed. ]Remove the cassette and cover the hole with adhesive tape, or

insert a cassette with the record safety tab intact.

The end of the tape was reached during Automatic Satellite Programme Recording.

]The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

]Turn off the timer mode by pressing REC LINK button or next operations cannot be carried on.

OTHER PROBLEMS

Whistling or howling is heard from the TV during camcorder recording.

The camcorder’s microphone is too close to the TV.

]Position the camcorder so its microphone is away from the TV.

The TV’s volume is too high. ]Turn the TV’s volume down.

When scanning channels, some of them are skipped over.

Those channels have been designated to be skipped.

]If you need the skipped channels, restore them. ( pg. 61)

Channel settings that were made manually seem to have changed or disappeared.

After the manual settings were made, Auto Channel Set was performed.

]Perform the manual settings again.

No channels are stored in the unit’s memory.

The TV aerial cable was not connected to the unit when Auto

Set Up was performed.

]Turn off the unit once and connect the TV aerial cable to the unit properly, then turn on the unit again. Then perform Auto Set Up again. ( pg. 14)

ATTENTION

This unit contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the unit off and unplug the mains power cord. Then plug it in again and turn the unit on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 69
Contents HR-XV38SAG HR-XV38SAS Use only discs marked with the following Safety PrecautionsContents Playable Discs About DiscsUnplayable Discs Region NumberPlacing a Disc File Structure of DiscsCare and Handling of Discs Open the disc trayFront View Tape Remaining Time Indicator pg Satellite Auto Recording Indicator N pgON-SCREEN Display VHS deck Counter Display Tape Speed SP/LP or EP* pgE Button rt Button Enter Button How To UseBasic Connections Check the contentsSituate the unit Connect the unit to TVPlug the end of the mains power cord into a mains outlet 10 ENBack of TV Switch the mode Scan Mode SetDVD deck Turn on the unitBack of TV Audio in connectors 8To connect to a TV with S-VIDEO/AUDIO in connectors12 EN Video ConnectionExit the Video Channel Set mode Access the Video Channel Set modeVideo Channel Set Set the video channel14 EN Auto Set UpSelect the mode setting Select the modeMonitor Set DVD deck Return to the normal screenLanguage 16 ENSelect the DVD deck Select the mode18 EN Language Code ListClock Set Start the clock operationTo make corrections anytime during the process Basic Playback 20 ENPlayback Features Instant ReView 22 ENRepeat Playback Manual TrackingBasic Recording Instant Timer Recording ITR Recording Features24 EN Tape Remaining TimeReceiving Stereo and Bilingual Programmes PlaybackRecording System Setup 26 ENGuide Program Number Set Access the G-CODE/SHOWVIEWscreen Timer ProgrammingAccess the G-CODEProgram screen Enter the G-CODEnumberTo Timer-Record Weekly Or Daily Serials Engage the unit’s timer mode28 EN Guide Program Number SetExpress Timer Programming Access the Programme Check screen Disengage the timer modeCancel or change a programme Return to the timer modeCancel or change programme setting When programmes overlap each otherConfirm the overlapping programmes Select the programme to modifyInput Connector Input L-1 connector Recording mode32 EN Press pPause playback Load the discStart playback PressAccess the DVD menu Locating a Desired Scene Using the DVD MenuAccess the PBC menu 34 ENZooming Locating the Start Point of the Item or Skip the Item36 EN Select the time Access the menuSelect the subtitle language If you have specified a wrong selection38 EN Select the audio settingAngle Selection Select the view angleSound Effect 3D Phonic VFP function Adjusting the picture qualityAccess the status bar How to Access the On-Screen BarAccess the menu bar 40 ENDuring playback, selects the audio language or sound track Menu Bar Functions for SVCD/Video CD/Audio CDDuring playback, selects the subtitle language During Video CD/SVCD playback, selects the audio channels42 EN PrecautionsOutline Control displaySelect the group Basic PlaybackControl display appears on the TV screen.  pg Press rt to select the desired group, then press e44 EN Group/File SelectionZooming a still picture Set the edit mode Set the unit’s input modeEngage the Record Pause mode Make connectionsEngage the Record Pause mode of the recording deck Set the input mode of recording deck46 EN Start the source playerFrom DVD to VHS DubbingPlace a disc and load an MD 48 ENPrepare the audio device for dubbing For the digital audio deviceSet the remote control code Change the remote control codeTurn off the unit Display the code50 EN Operating a JVC TVOperate the TV Satellite receiver Connecting To a Satellite ReceiverMake connections 52 ENFunction Set VHS deck Access the Mode Set screenPress rt to move the highlight bar pointer to Function SET, then press54 EN Subsidiary SettingsFor Example Auto Splp Timer on / OFFMode Set DVD deck Access the DVD Set Up menu screen56 EN Picture Settings Audio SettingsSet this item correctly according to the logo on the device 58 EN Others SettingsParental Lock Playback discsCountry/Area Code List for Parental Lock 60 EN Access the Auto Channel Set screenTuner Set Auto Channel SetManual Channel Set 62 EN Delete a ChannelSwap Channel Position Select the channel to fine-tune Perform tuningSelect the channel FRQ number for the channel starts blinking64 EN Slide to the right You can disable the unit’s operationChild Lock Set the Child LockVHS deck Off-Air Recording Information on Multi-System CompatibilityTV System Recorded tapeTape-To-Tape Editing 66 ENRecorded tape Playback equipment Recording circuitTape Transport VHS deck PowerPlayback VHS deck Playback DVD deck68 EN Input mode is not correct Set the input mode to L-1 or F-1MP3/JPEG Files Playback DVD deck Recording VHS deckTimer recording won’t work Timer Recording VHS deck70 EN TUNER/TIMER VHS deckVIDEO/AUDIO VHS deck VIDEO/AUDIO DVD deckConnecting To a Dolby Digital Decoder or An Amplifier Auto Channel Set Auto Set UpExpress Timer Programming CODE/SHOWVIEW System SetupHR-XV38SAG/HR-XV38SAS