JVC LPT0976-001B manual Basic Connection, To connect to a TV with 21-pin Scart input connector

16 EN INSTALLING YOUR NEW UNIT

Basic Connections		THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO
		OPERATION CAN BE PERFORMED.
		1	Make sure the package contains all of the accessories listed in
		2	ASPECIFICATIONSB (A pg. 94).
			Place the unit on a stable, horizontal surface.
		3	Connect the unit to a TV depending on the TV and cables you
			use.
	TV aerial cable	8	Basic Connection
		To connect to a TV with 21-pin SCART input connector ^
		A Disconnect the TV aerial cable from the TV.
		B Connect the TV aerial cable to the [ANTENNA IN] connector on
			the rear panel of the unit.
		C Connect the [ANTENNA OUT] connector on the rear panel of
Mains outlet	To [ANTENNA IN]		the unit and the TV’s aerial connector with the supplied RF
			cable.
		D Connect the [L-1 IN/OUT] connector on the rear panel of the
Mains power cord			unit and the TV’s 21-pin SCART connector with a supplied 21-
			pin SCART cable.
Back of unit		● The [L-1 IN/OUT] connector accepts and delivers either a
			composite signal (regular video signal), Y/C signal or RGB
			signal.
		● Set your TV to the VIDEO (or AV), Y/C, or RGB mode
			according to the type of your TV’s SCART connector.

			8 Component Video Connection
To [AUDIO	To [COMPONENT	To [L-1 IN/	To connect to TV’s component video input connectors ^
	VIDEO OUT (Y/PB/	OUT]	A Perform A – C in ABasic ConnectionB.
OUT]
	PR)]	To	B Connect the unit’s [COMPONENT VIDEO OUT (Y/PB/PR)]
		[ANTENNA	connectors to the TV’s component video input connectors.
		OUT]	C Connect the unit’s [AUDIO OUT] connectors to the TV’s AUDIO
	Component		input connectors.
		21-pin SCART	● You can obtain high-quality component video pictures.
Audio cable	video cable		● If your TV is not stereo-capable, use the unit’s [AUDIO OUT]
	(not supplied)	cable	connectors to connect to an audio amplifier for Hi-Fi stereo
(not supplied)
		(supplied)
			sound reproduction.
			● By using the component video connection, you can view the
			images in the progressive mode. For switching to the
			progressive mode, refer to AScan Mode SetB (A pg. 89).
		RF cable	● You can also watch the images on the VHS deck in Progressive
		(supplied)	scan mode via the component video output, refer to AVHS
			Progressive ScanB (A pg. 43).
		TV	NOTE:
		To 75 ohm	Select an appropriate option of AL-1 OUTPUTB as follows
			(A pg. 72):
		terminal
It’s essential that your unit be properly connected.			When your TV’s SCART	Set AL-1 OUTPUTB to:
			connector accepts:

ATTENTION:	Composite signals	ASCART VIDEOB
● Your TV must have a 21-pin AV input connector (SCART) for	Y/C signal (separated
the basic connection to the unit.	luminance (brightness) and	ASCART S-VIDEOB
● Connect the AC plug only after all connections to the TV has	chrominance (colour) signals)
been completed.
	RGB signal	ASCART RGBB
	Component video signal	ACOMPONENTB

When the setting selected is not in accordance with the TV connected and depending on the type of appliance connected to the unit, the correct picture will not appear.

4 Plug the end of the mains power cord into a mains outlet.

● ALOADINGB blinks on the front display panel when the AC plug of the mains power cord is connected into a mains outlet and it takes approximately 50 seconds for the unit to be turned on.

This is not a malfunction.