JVC 1204MNH-SW-VE, LPT0976-001B Digital Audio Dubbing, Input Setting, Example Dubbing to an MD

					EDITING EN 73
SAT S-VIDEO:		Digital Audio Dubbing
If a connected satellite receiver’s output is compatible with Y/C
signals, set to ASAT S-VIDEOB. You can obtain a high-quality
	You can dub selected audio from a DVD or Audio CD disc to a
S-VHS picture. (For connection, be sure to use a 21-pin
SCART cable that is compatible with the Y/C signal.)	digital audio device.
DECODER:	However, it is not possible to dub copy-protected discs.
To use a decoder connected to the [L-2 IN/DECODER] connector.
	● Turn on the TV and select the AV mode.
NOTES:	● Slide the TV/CABLE/SAT/DVD switch to DVD.
● If you have a satellite receiver or a decoder connected to the [L-2
	Example: Dubbing to an MD
IN/DECODER] connector, be sure to set AL-2 SELECTB back to
appropriate mode after editing.				Recorder
● If you are not connecting a satellite receiver or a decoder to the
[L-2 IN/DECODER] connector, leave AL-2SELECTB set to
AVIDEOB.
● When AL-2 SELECTB is set to ASAT VIDEOB and ASAT S-VIDEOB,
ASATB appears on the TV screen or front display panel instead of
AL-2B.
● If AL-1 OUTPUTB is set to ASCART S-VIDEOB, it is not possible to
set AL-2 SELECTB to ADECODERB or ASAT VIDEOB.			Digital audio device
● If AL-1 OUTPUTB is set to ASCART RGBB, it is not possible to set
			(MD deck, etc.)
AL-2 SELECTB to ADECODERB or ASAT S-VIDEOB.

●If AL-1 OUTPUTB is set to ACOMPONENTB and AL-2 SELECTB to ASAT VIDEOB, ASAT S-VIDEOBor ADECODERB, be sure to

connect the [L-1 IN/OUT] connector with a TV.					Coaxial cable	Optical cable
					(not supplied)	(not supplied)
● If AL-2 SELECTB is set to ASAT S-VIDEOB, be sure to set AL-1
OUTPUTB to ASCART S-VIDEOB.
F-1 Input Setting					To [DIGITAL	To [DIGITAL
					AUDIO OUT	AUDIO OUT
Set AF-1 INPUTB to the appropriate mode depending on the				Player	(COAXIAL)]	(OPTICAL)]
connector (VIDEO or S-VIDEO) being used on the front panel.
1 Perform steps 1 and 2 of AL-1 Output And L-1 Input SettingB
(A pg. 72).
2 Press FG to select AF-1 INPUTB, then press ENTER.
3 Press FG to select the						Rear of unit
appropriate setting, then press	DVD VIDEO SET UP	HDD/DVD SET UP FUNCTION SET UP INITIAL SET UP
	REC/PLAY SET UP	DISPLAY SET	VIDEO IN/OUT
ENTER.	MONITOR TYPE		4:3LB
4 Press SET UP to complete the
	F-1 INPUT		VIDEO VIDEO
setting.	L-1 OUTPUT		S-VIDEO
	L-1 INPUT		SCART VIDEO

L-2 SELECT		VIDEO
SET UP	ENTER	SELECT WITH @ THEN PRESS [ENTER]
EXIT	SELECT	PRESS [SET UP] TO EXIT

Note for connection:

Remove the protection cap from the optical cable.

* The boldface settings below indicate the settings at your purchase.

8F-1 INPUT ^ VIDEO / S-VIDEO VIDEO:

When connecting an appliance to the [VIDEO] input connector, set to AVIDEOB.

S-VIDEO:

When connecting an appliance to the [S-VIDEO] input connector, set to AS-VIDEOB.

1Connect the unit and a digital audio device using either an optional optical cable or an optional coaxial cable.

2Place a disc on the unit and load an MD on the connected digital audio device.

3Select the audio to be dubbed.

4Start playback slightly before the actual point from where you wish to start dubbing.

5Press W to pause playback.

6Select the input mode on the connected digital audio device.

7Press I to start playback on the unit.

8Start recording on the digital audio device.

9Stop recording on the digital audio device. Then press o to stop playback on the unit.

NOTE:

There may be a discrepancy of several seconds between where you intend editing to start, and where it actually starts.