JVC LPT0976-001B, 1204MNH-SW-VE Remote control switch, Auto capture button, Sound monitor switch

68 EN EDITING

DV Dubbing (HDD & DVD Deck Only)	The following on-screen display for DV dubbing appears when
	ON SCREEN is pressed while the channel has been set to ADVB.

You can dub programmes from a camcorder or DV equipment connected to the unit with a DV cable. The unit’s remote control allows you the limited control of the connected camcorder or DV equipment functions during dubbing.

	HDD	0:00	1:00		2:00 GR-DV3500	DV
FR360	00:00:00. 00				00:00:00. 00	L – R
12bit	DV	JVC		GR-DV3500		SOUND1

NOTES:

●Use the DV cable VC-VDV 204U for connection.

●When you connect a PC to the [DV IN] connector, we do not assure the normal operation of this unit.

Your unit

To [DV IN]

DV DV 1 2

A B C

ARemote control switch

To switch between the devices operable by the remote control

unit. The unit is operable when the remote icon ( ) displayed faces to the left, while the DV device is operable when the remote icon is facing to the right.

BAuto capture button

Select to start or pause the dubbing. If ENTER is pressed when the DV device is in the pause condition, preroll editing* where it is possible to dub with a start time that is highly accurate will be activated. When the DV device cannot be operated from the unit (such as in camera mode), proceed with normal recording (A pg. 34, 37).

*Preroll editing refers to the playback after the DV tape is slightly rewind. (For DV devices that do not support the –1x speed, the rewinding time may be longer.)

Camcorder

DV equipment

DV cable (VC-VDV 204U)

(not supplied)

DV connector

CSound monitor switch

For selecting the desired sound format for dubbing.

1Connect a camcorder or DV equipment to the [DV IN] connector on the unit’s front panel.

2Press VHS/HDD/DVD SELECT on the unit repeatedly or HDD on the remote so that the HDD lamp lights up on the unit.

3Press PR +/– to set the channel to ADVB.

4Press ON SCREEN.

●The on-screen display for DV dubbing appears.

5Press DE to select , then press ENTER to display the remote icon (facing to the right) for the DV equipment.

6Press REC MODE repeatedly to set the recording mode.

7Locate the point from where you want to start dubbing, then

stop or pause playback by pressing the following buttons on the remote control: I, N, O, o, W.

●To play back in slow speed (1/10 of the normal speed), press W to pause playback, then press O or N.

●To play back frame-by-frame, press W to pause playback, then press W repeatedly. Each press of W advances a frame.

●To change the playback direction, press O or N.

8Press DE to select , then press ENTER repeatedly until the desired sound track appears on the TV screen.

SOUND 1:

Select this to record the original stereo sound played back on the connected DV equipment.

SOUND 2:

Select this to record the dubbed stereo sound played back on the connected DV equipment.

MIX:

Select this to record the sound of both ASOUND 1B and ASOUND 2B.

●Note that this selection is not available when the source programme is recorded in 16BIT (48 kHz) mode.

9Press DE to select , then press ENTER. The dubbing starts.

●Playback on the external DV equipment and recording on the unit should start simultaneously.

●To pause dubbing, press DE to select , then press ENTER. Both the unit and the external DV equipment pause dubbing. Pressing W on the unit also works the same way.

10Press DE to select , then press ENTER. Then press o. The DV equipment stops.

11Press DE to select , then press ENTER.