JVC LPT0976-001B manual Playback DVD Deck, Initialising DVD Deck Only, General, Playback HDD Deck

90 EN TROUBLESHOOTING

Before requesting service for a problem, use this chart and see if	Playback (DVD Deck)
you can solve the trouble yourself. Small problems are often easily
solved, and this can save you the trouble of sending your unit off	The DVD deck cannot be operated.
for repair.
	● The DVD deck is not selected.
Initialising (DVD Deck Only)
	N Press VHS/HDD/DVD SELECT on the unit repeatedly or DVD
	on the remote so that the DVD lamp lights up on the unit.
Malfunction occurs on the unit.
	Images do not appear on the TV screen.

NPress A to turn off the unit, press and hold A, then press o

for two seconds or more.	● The TV receiver’s channel selector is not set to the AV mode.
	N Set the TV to its AV mode.
General	● When interlace scanned programme is played back,
	progressive scan mode is selected.
	N Press and hold PROGRESSIVE SCAN until q disappears
No power is supplied to the unit.
	from the front display panel. (A pg. 89)

●The AC power plug is disconnected from the mains outlet.

N Connect the AC power plug to the mains outlet securely.	Playback does not start or stop immediately after playback is
(A pg. 16)	started by pressing I.
	On the front display panel, ANO DISCB appears.
The remote control does not work properly.
	● The disc is loaded upside down.
N Remove the batteries, wait for 5 minutes or more, then load the
	N Place the disc on the disc tray with the playback surface facing
butteries again.	down. (A pg. 8)
● The setting of the remote control code is inappropriate.	● A disc not being compatible with the unit is loaded.
N Set the same remote control code (1, 2, 3, or 4) on both the unit	N Load a playable disc on the unit. (A pg. 5)
and the remote control. (A pg. 74)	● A dirty disc is loaded.
● The batteries are discharged.	N Clean the disc. (A pg. 9)
N Replace the dead batteries with new ones.	● Defective disc is loaded.
	N Replace the warped or scratched disc with a normal one.
Dubbing from the external equipment is not possible.
● The source (another video recorder, camcorder) has not been	Images are blurred or distorted when you start High-Speed
	Search.
properly connected.
N Confirm that the source is properly connected.	N Images are blurred or distorted at the point where the playback
● All necessary power switches have not been turned on.	speed changes and this is not a malfunction of the unit.
N Confirm that all units’ power switches are turned on.
● The setting of the input channel position is inappropriate.	Playback does not start.
N Select the input channel position (AF-1B, AL-1Bor AL-2B) that	N Playback does not start for approximately 30 seconds after
corresponds to the input terminal connected to the external
	recording is stopped and this is not a malfunction of the unit.
equipment. (A pg. 71)
	Playback does not start when you select a title or a chapter.
The on-screen display superimposed on the programme
played back/received on this unit is recorded when you dub	● The Parental Lock is engaged and the disc is rated higher than
the programme to an external recording equipment.	the set level.
N Set ASUPERIMPOSEB or AO.S.D.B to AOFFB. (A pg. 80, 81)	N Release the Parental Lock temporarily or change the set level.
	(A pg. 33)
The unit does not operate.	Playback (HDD Deck)
● There are cases when the operation is prohibited on the disc.
● Lightning or static electricity may cause malfunction of the unit.	The HDD deck cannot be operated.
N Press A to turn the power off, then press the button again to
	● The HDD deck is not selected.
turn the power on.
	N Press VHS/HDD/DVD SELECT on the unit repeatedly or HDD

The remote control of a JVC TV will not operate the unit.

●The setting of the remote control code is inappropriate.

N To operate the unit using a JVC TV remote control, set the remote control code of the unit to A1B (Default: A3B). (A pg. 74)

on the remote so that the HDD lamp lights up on the unit.