Q-See QSD2216 manual Motion Detection settings, When surveying nearby objects 2-10 meters

Page 25

5.6.1Motion Detection settings

ALARM ENABLE: alarm trigger switch, can be set to off, N.C(normal closed) or N.O(normal open). If users set it to off, the DVR will ignore the alarm input.

MOTION ENABLE: Motion alarm switch, can be set to ON or OFF. If set to off, the DVR will ignore the motion alarm.

MOTION LEVEL: motion sensitivity level, if the figure in the picture is small, please set to high or very high, default is normal.

BUZZER TIME: buzzer sound time when there is a sensor or motion alarm.

SENSE RECTIME: when a motion or sensor alarm is triggered, the recording time of DVR, default is 10 seconds.

Notice: Users should press the schedule button after setting up the parameters to activate the settings.

5.6.1Motion Detection settings

1)When surveying nearby objects (2-10 meters)

When in daytime, please set motion detection sensitivity to Normal level; when in night,

please set to low.

2) When surveying objects in 50-100 meters area

The objects 50-100 meters away will be quite small on the screen. When in daytime, please

set motion detection sensitivity to high level.

25

Image 25

Contents Page About this document Safety PrecautionsWarranty and Service Before reading this document Strong recommendation on installation of the DVR unitCONTENTS 1. FEATURE AND FUNCTION 2.1 Recording/Playing Control Buttons Area 2. UNIT DESCRIPTION OF FRONT PANEL2.2 Function Control Area 1. Auto/1 Auto key, in shift mode, press this button, The DVR will be in auto dwell state, it dwells according to the time set in auto sequence set menu, and you can set the dwell time of each channel. Press this button to quit this mode. If not in shift mode, press this button to see big picture of channel 1. While inputting numbers, this button is used as number key of “1” 2.3 Channel Choosing Control Area 3. REAR PANEL AND SYSTEM CONNECTION3.1 Back panel and connection terminals 3.3 Alarm Connection3.2 Video and Audio Connection Alarm output There are processing to install the hard disk 3.4 Hard Disk Connection5. SYSTEM SETUP 4. REMOTE CONTROLLER5.1 SETUP MENU Page 5.2.1 TIME/DATA SET 5.2 SYSTEM SETUP5.2.2 HDD FORMAT SET 5.2.3 FACTORY RESET5.2.4 Change Password 5.2.5 Firmware Update 5.3.1 CAMERA NAME SET 5.3 DISPLAY SETUP5.3.2 COLOR SET 5.3.3. AUTO SEQUENCE SET 5.4 RECORD SETUP5.4.1 AUDIO CH SET 5.4.2 REC CH SET 5.5 NETWORK SETUP5.5.1. N/W ENABLE SET 5.5.2. MAC SET 5.6 SENSOR SETUP1 When surveying nearby objects 2-10 meters 5.6.1 Motion Detection settings2 When surveying objects in 50-100 meters area 5.6.2 MOTION AREA SET 5.7 SCHEDULE SET 5.8 USB BACKUP5.10 PTZ SET 5.9 STORAGE INFO6.1 Start the DVR 6. Quick User Guideline6.2 Turn off the DVR 6.3 Normal Recording6.5 Time Recording 6.4 Alarm Recording6.6 Playback 6.7 Search Play 6.9 Event Search 6.8 Time Search6.10 Record Search 6.11 USB Backup 6.13 Zoom Operation 6.12 USB Update6.15 PTZ Operation 6.14 Information DisplayPress the PTZ button one more time to exit from PTZ control 6.16 REMOTE CONTROLLER 7. USING THE NETWORK VIEWER7.2 Viewer connect 7.1 SettingPlease click button, you will see the window below Enter the IP address and click “OK” button7.4 Playback 7.3 Live play7.6 File Play 7.5 Scandisk7.7 Save to AVI 7.9 PTZ Control 7.8 Save to DVR8. Main standard & parameter chart 9. Trouble shooting guide Q. Why cannot I access Network Set menu? A. Please stop record or play before you access these menuQ. I press record button, but the DVR does not start recording, why? Q. There is a movement, but the DVR does not start recording10. Record Time Table ResolutionRec rate field/sec Picture quality11.2 Network Configurations 11. Internet View/Playback Configurations11.1 About Networks Page Page Q-SEE Product Warranty Address Postal code Phone Number E-mail Model Number of Product Customer Information Card User’s NameMr./Mrs Company Name PostalSerial Number of Product Purchase Date Distributor