Q-See QSD2216 manual Alarm output

Page 10

Alarm output:

2.Open/Close output

A:N.O. Normal open, close when triggered. DVR must set as low voltage alarm.

B:N.C. Normal close, open when triggered. DVR must set as high voltage alarm. Please refer to the picture below, channel 2 to channel 16 are the same as channel 1.

Alarm output:

There are three alarm output pin, the status of these pin are illustrated as below

Before Alarm

After Alarm

There is an example for alarm output connection

10

Image 10

Contents Page About this document Safety PrecautionsWarranty and Service Strong recommendation on installation of the DVR unit Before reading this documentCONTENTS 1. FEATURE AND FUNCTION 2.1 Recording/Playing Control Buttons Area 2. UNIT DESCRIPTION OF FRONT PANEL2.2 Function Control Area 1. Auto/1 Auto key, in shift mode, press this button, The DVR will be in auto dwell state, it dwells according to the time set in auto sequence set menu, and you can set the dwell time of each channel. Press this button to quit this mode. If not in shift mode, press this button to see big picture of channel 1. While inputting numbers, this button is used as number key of “1” 3. REAR PANEL AND SYSTEM CONNECTION 2.3 Channel Choosing Control Area3.1 Back panel and connection terminals 3.3 Alarm Connection3.2 Video and Audio Connection Alarm output 3.4 Hard Disk Connection There are processing to install the hard disk5. SYSTEM SETUP 4. REMOTE CONTROLLER5.1 SETUP MENU Page 5.2 SYSTEM SETUP 5.2.1 TIME/DATA SET5.2.3 FACTORY RESET 5.2.2 HDD FORMAT SET5.2.4 Change Password 5.2.5 Firmware Update 5.3 DISPLAY SETUP 5.3.1 CAMERA NAME SET5.3.2 COLOR SET 5.4 RECORD SETUP 5.3.3. AUTO SEQUENCE SET5.4.1 AUDIO CH SET 5.5 NETWORK SETUP 5.4.2 REC CH SET5.5.1. N/W ENABLE SET 5.6 SENSOR SETUP 5.5.2. MAC SET1 When surveying nearby objects 2-10 meters 5.6.1 Motion Detection settings2 When surveying objects in 50-100 meters area 5.6.2 MOTION AREA SET 5.8 USB BACKUP 5.7 SCHEDULE SET5.9 STORAGE INFO 5.10 PTZ SET6.2 Turn off the DVR 6. Quick User Guideline6.1 Start the DVR 6.3 Normal Recording6.5 Time Recording 6.4 Alarm Recording6.6 Playback 6.7 Search Play 6.8 Time Search 6.9 Event Search6.10 Record Search 6.11 USB Backup 6.12 USB Update 6.13 Zoom Operation6.14 Information Display 6.15 PTZ OperationPress the PTZ button one more time to exit from PTZ control 7. USING THE NETWORK VIEWER 6.16 REMOTE CONTROLLERPlease click button, you will see the window below 7.1 Setting7.2 Viewer connect Enter the IP address and click “OK” button7.3 Live play 7.4 Playback7.5 Scandisk 7.6 File Play7.7 Save to AVI 7.8 Save to DVR 7.9 PTZ Control8. Main standard & parameter chart 9. Trouble shooting guide Q. I press record button, but the DVR does not start recording, why? A. Please stop record or play before you access these menuQ. Why cannot I access Network Set menu? Q. There is a movement, but the DVR does not start recordingRec rate field/sec Resolution10. Record Time Table Picture quality11.2 Network Configurations 11. Internet View/Playback Configurations11.1 About Networks Page Page Q-SEE Product Warranty Address Postal code Phone Number E-mail Model Number of Product Customer Information Card User’s NameMr./Mrs Company Name PostalSerial Number of Product Purchase Date Distributor