Q-See QSD2216 manual Alarm Recording, Time Recording, Playback

Page 30

6.4 Alarm Recording

Alarm recording is not started by manually pressing the Record button, it is automatically activated once Schedule mode is enabled. Alarm recording can be activated by alarm input signal or motion, if the connection of alarm input equipment is correct, stable and reliable, and the alarm settings are correct. For recording to be activated by exterior input signal or motion detection the system must be set to Schedule Mode active and that period is set to “A” in Record Schedule setup. You must also set the menu of Alarm Setup for exterior input alarm, and the alarm enable setting of that channel must be set to “ON”. For Motion Alarm, the motion enable setting of that channel must set “ON”, and set the area for motion detection must be set. If Schedule mode is disabled the system will not start recording on alarm. Setting schedule on or off is achieved through pressing the SCHEDULE button on the front panel or remote, but not through the System Setup menu and window. When the unit is in Schedule Mode active, the character “S” will display on the screen. Alarm video recording can’t be stopped by pressing the RECORD or STOP button while Schedule Mode is active. To ensure that once Schedule Mode is set to on that the schedule cannot be accidentally stopped there is a password protection to stop Schedule Mode. You must press the SCHEDULE button then enter the correct password to turn Schedule Mode off. Check Alarm Recording setup before recording; confirm the video quality and the frame rate, as the record setting can’t be changed during the recording process. As long as the alarm input signal is correctly set the alarm recording will continue during the period of time set up by A/M REC TIME, and when the outside the time period the alarm recording automatically stops.

6.5 Time Recording

Time recording starts and stops recording automatically according to the pre-arranged time period. It is applied to a fixed timetable, for example business hours time recording (or outside business hours time recording) with fixed start/stop time. To start the Time Recording function you must have a record schedule setup beforehand. When this is done, press the SCHEDULE button on the front panel to set schedule mode to on and the schedule symbol “S” will display on the screen. The Time Recording mode will not work unless you activate Schedule Mode. To make Time Recording mode active the system must be set to Schedule Mode active and that period is set to “T” in Record Schedule setup. In Time Record mode, you must press the SCHEDULE button then enter the password to stop time recording. Because Time recording is reliant on the system being set with the correct time, you must adjust the time to your correct local time before using this function.

6.6 Playback

Press the PLAY button and the system will begin to play the images recorded from the start of the most current recording.

If the recording is playing, press the PAUSE button to pause playing, press the PLAY button again to resume normal play.

To use Fast Forward playing or Fast Backward playing, press the FWD or REW button while the

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Page Safety Precautions About this documentWarranty and Service Strong recommendation on installation of the DVR unit Before reading this documentCONTENTS 1. FEATURE AND FUNCTION 2. UNIT DESCRIPTION OF FRONT PANEL 2.1 Recording/Playing Control Buttons Area2.2 Function Control Area 1. Auto/1 Auto key, in shift mode, press this button, The DVR will be in auto dwell state, it dwells according to the time set in auto sequence set menu, and you can set the dwell time of each channel. Press this button to quit this mode. If not in shift mode, press this button to see big picture of channel 1. While inputting numbers, this button is used as number key of “1” 3. REAR PANEL AND SYSTEM CONNECTION 2.3 Channel Choosing Control Area3.3 Alarm Connection 3.1 Back panel and connection terminals3.2 Video and Audio Connection Alarm output 3.4 Hard Disk Connection There are processing to install the hard disk4. REMOTE CONTROLLER 5. SYSTEM SETUP5.1 SETUP MENU Page 5.2 SYSTEM SETUP 5.2.1 TIME/DATA SET5.2.3 FACTORY RESET 5.2.2 HDD FORMAT SET5.2.4 Change Password 5.2.5 Firmware Update 5.3 DISPLAY SETUP 5.3.1 CAMERA NAME SET5.3.2 COLOR SET 5.4 RECORD SETUP 5.3.3. AUTO SEQUENCE SET5.4.1 AUDIO CH SET 5.5 NETWORK SETUP 5.4.2 REC CH SET5.5.1. N/W ENABLE SET 5.6 SENSOR SETUP 5.5.2. MAC SET5.6.1 Motion Detection settings 1 When surveying nearby objects 2-10 meters2 When surveying objects in 50-100 meters area 5.6.2 MOTION AREA SET 5.8 USB BACKUP 5.7 SCHEDULE SET5.9 STORAGE INFO 5.10 PTZ SET6.2 Turn off the DVR 6. Quick User Guideline6.1 Start the DVR 6.3 Normal Recording6.4 Alarm Recording 6.5 Time Recording6.6 Playback 6.7 Search Play 6.8 Time Search 6.9 Event Search6.10 Record Search 6.11 USB Backup 6.12 USB Update 6.13 Zoom Operation6.14 Information Display 6.15 PTZ OperationPress the PTZ button one more time to exit from PTZ control 7. USING THE NETWORK VIEWER 6.16 REMOTE CONTROLLERPlease click button, you will see the window below 7.1 Setting7.2 Viewer connect Enter the IP address and click “OK” button7.3 Live play 7.4 Playback7.5 Scandisk 7.6 File Play7.7 Save to AVI 7.8 Save to DVR 7.9 PTZ Control8. Main standard & parameter chart 9. Trouble shooting guide Q. I press record button, but the DVR does not start recording, why? A. Please stop record or play before you access these menuQ. Why cannot I access Network Set menu? Q. There is a movement, but the DVR does not start recordingRec rate field/sec Resolution10. Record Time Table Picture quality11. Internet View/Playback Configurations 11.2 Network Configurations11.1 About Networks Page Page Q-SEE Product Warranty Customer Information Card User’s NameMr./Mrs Company Name Postal Address Postal code Phone Number E-mail Model Number of ProductSerial Number of Product Purchase Date Distributor
Top Page Image Contents