Q-See QSD2216 manual Quick User Guideline, Start the DVR, Turn off the DVR, Normal Recording

Page 29

CHANNEL SEL: If you have a speed dome camera, select the channel which the camera is connected to.

BAUD RATE: Changeable from 1200bps to 115200bps. The default value is 2400bps.

DOME ADDR: The address of the speed dome camera, changeable from 0x00 to 0xff.

PROTOCOL: The protocol of speed dome camera: PELCO-D,PELCO-P,NEON,SAMSUNG

6. Quick User Guideline

6.1 Start the DVR

Before starting the DVR, please make sure all the items in the “Security Notice” at the beginning of this manual are fulfilled and that the input and output cables are all correctly connected.

Also ensure the DVR’s video input format (NTSC/PAL) and the monitor (NTSC/PAL) are both set to the same video standard. NTSC for USA & Canada, PAL for Australia, UK and most of Europe. Fit the hard disk to the removable caddy and insert the removable caddy into the housing, then lock it up (turn the hard disk lock to the right) and connect the power which will then boot the DVR and it will start to work.

6.2 Turn off the DVR

Only turn off the DVR when the system is inactive. Do not to turn off the DVR while playing or doing the System Setup. Turning off the DVR while recording may cause the recording to corrupt, and can cause the HDD to be unreadable in some cases.

Press the Record button to stop recording or press Stop button to stop playing or exit from System Setup menu, then turn off the power.

If do not wish use the video recorder for a long time, you should pull out the power line from the electrical outlet and store the unit where it will not be damaged.

6.3 Normal Recording

Connect the power to all related equipment; ensure that there is video input using direct connection to your TV or VCR. Press the Display button to check spare space of the hard disk, if there is not much space, please consider changing your hard disk first or select Overwrite mode. Check recording parameter setup before recording; select video quality, frame rate. Note that you cannot change record setting during the process of recording. Manual recordings are the normal recording condition. Under the manual mode (non-schedule status),

pressing the Record button will record all channel’s video. Press the Record button to begin recording, four channels will start simultaneous recording. While in normal recording mode, press the Record or Stop button, and enter the right password, to stop recording. During the process of recording if the hard disk is full and the system is set to automatic overwrite, the recording will not be interrupted but the DVR will automatically begin to overwrite recorded video from the earliest (oldest) recorded area. If the system is set to overwrite disabled, it will stop recording once the HDD is full.

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Page Warranty and Service Safety PrecautionsAbout this document Before reading this document Strong recommendation on installation of the DVR unitCONTENTS 1. FEATURE AND FUNCTION 2.2 Function Control Area 2. UNIT DESCRIPTION OF FRONT PANEL2.1 Recording/Playing Control Buttons Area 1. Auto/1 Auto key, in shift mode, press this button, The DVR will be in auto dwell state, it dwells according to the time set in auto sequence set menu, and you can set the dwell time of each channel. Press this button to quit this mode. If not in shift mode, press this button to see big picture of channel 1. While inputting numbers, this button is used as number key of “1” 2.3 Channel Choosing Control Area 3. REAR PANEL AND SYSTEM CONNECTION3.2 Video and Audio Connection 3.3 Alarm Connection3.1 Back panel and connection terminals Alarm output There are processing to install the hard disk 3.4 Hard Disk Connection5.1 SETUP MENU 4. REMOTE CONTROLLER5. SYSTEM SETUP Page 5.2.1 TIME/DATA SET 5.2 SYSTEM SETUP5.2.2 HDD FORMAT SET 5.2.3 FACTORY RESET5.2.4 Change Password 5.2.5 Firmware Update 5.3.1 CAMERA NAME SET 5.3 DISPLAY SETUP5.3.2 COLOR SET 5.3.3. AUTO SEQUENCE SET 5.4 RECORD SETUP5.4.1 AUDIO CH SET 5.4.2 REC CH SET 5.5 NETWORK SETUP5.5.1. N/W ENABLE SET 5.5.2. MAC SET 5.6 SENSOR SETUP2 When surveying objects in 50-100 meters area 5.6.1 Motion Detection settings1 When surveying nearby objects 2-10 meters 5.6.2 MOTION AREA SET 5.7 SCHEDULE SET 5.8 USB BACKUP5.10 PTZ SET 5.9 STORAGE INFO6.1 Start the DVR 6. Quick User Guideline6.2 Turn off the DVR 6.3 Normal Recording6.6 Playback 6.4 Alarm Recording6.5 Time Recording 6.7 Search Play 6.9 Event Search 6.8 Time Search6.10 Record Search 6.11 USB Backup 6.13 Zoom Operation 6.12 USB Update6.15 PTZ Operation 6.14 Information DisplayPress the PTZ button one more time to exit from PTZ control 6.16 REMOTE CONTROLLER 7. USING THE NETWORK VIEWER7.2 Viewer connect 7.1 SettingPlease click button, you will see the window below Enter the IP address and click “OK” button7.4 Playback 7.3 Live play7.6 File Play 7.5 Scandisk7.7 Save to AVI 7.9 PTZ Control 7.8 Save to DVR8. Main standard & parameter chart 9. Trouble shooting guide Q. Why cannot I access Network Set menu? A. Please stop record or play before you access these menuQ. I press record button, but the DVR does not start recording, why? Q. There is a movement, but the DVR does not start recording10. Record Time Table ResolutionRec rate field/sec Picture quality11.1 About Networks 11. Internet View/Playback Configurations11.2 Network Configurations Page Page Q-SEE Product Warranty Serial Number of Product Purchase Date Distributor Customer Information Card User’s NameMr./Mrs Company Name PostalAddress Postal code Phone Number E-mail Model Number of Product
Top Page Image Contents