Q-See QSD2216 manual Motion Area Set

Page 26

5.6.2 MOTION AREA SET

When in night as below, please set to normal level.

Note: the above suggestions are a guide only based on testing in a general environment. You will need to select the best parameters according to the actual operation environment you are covering. Try different settings until you get the desired motion detection result.

5.6.2 MOTION AREA SET

Move the cursor to Motion Area Set, then press the Enter button, and the area setup window will appear. Press the up, down, left, right button to move the cursor and press the Enter button to change from detection ON to OFF. Press and hold the Enter button to change all values to the same as the area you have selection.

If the area marker icon is set to yellow, this area is monitored for motion detection, and if the icon is blue, motion sensing is disabled for that area.

26

Image 26

Contents Page Warranty and Service Safety PrecautionsAbout this document Strong recommendation on installation of the DVR unit Before reading this documentCONTENTS 1. FEATURE AND FUNCTION 2.2 Function Control Area 2. UNIT DESCRIPTION OF FRONT PANEL2.1 Recording/Playing Control Buttons Area 1. Auto/1 Auto key, in shift mode, press this button, The DVR will be in auto dwell state, it dwells according to the time set in auto sequence set menu, and you can set the dwell time of each channel. Press this button to quit this mode. If not in shift mode, press this button to see big picture of channel 1. While inputting numbers, this button is used as number key of “1” 3. REAR PANEL AND SYSTEM CONNECTION 2.3 Channel Choosing Control Area3.2 Video and Audio Connection 3.3 Alarm Connection3.1 Back panel and connection terminals Alarm output 3.4 Hard Disk Connection There are processing to install the hard disk5.1 SETUP MENU 4. REMOTE CONTROLLER5. SYSTEM SETUP Page 5.2 SYSTEM SETUP 5.2.1 TIME/DATA SET5.2.3 FACTORY RESET 5.2.2 HDD FORMAT SET5.2.4 Change Password 5.2.5 Firmware Update 5.3 DISPLAY SETUP 5.3.1 CAMERA NAME SET5.3.2 COLOR SET 5.4 RECORD SETUP 5.3.3. AUTO SEQUENCE SET5.4.1 AUDIO CH SET 5.5 NETWORK SETUP 5.4.2 REC CH SET5.5.1. N/W ENABLE SET 5.6 SENSOR SETUP 5.5.2. MAC SET2 When surveying objects in 50-100 meters area 5.6.1 Motion Detection settings1 When surveying nearby objects 2-10 meters 5.6.2 MOTION AREA SET 5.8 USB BACKUP 5.7 SCHEDULE SET5.9 STORAGE INFO 5.10 PTZ SET6.2 Turn off the DVR 6. Quick User Guideline6.1 Start the DVR 6.3 Normal Recording6.6 Playback 6.4 Alarm Recording6.5 Time Recording 6.7 Search Play 6.8 Time Search 6.9 Event Search6.10 Record Search 6.11 USB Backup 6.12 USB Update 6.13 Zoom Operation6.14 Information Display 6.15 PTZ OperationPress the PTZ button one more time to exit from PTZ control 7. USING THE NETWORK VIEWER 6.16 REMOTE CONTROLLERPlease click button, you will see the window below 7.1 Setting7.2 Viewer connect Enter the IP address and click “OK” button7.3 Live play 7.4 Playback7.5 Scandisk 7.6 File Play7.7 Save to AVI 7.8 Save to DVR 7.9 PTZ Control8. Main standard & parameter chart 9. Trouble shooting guide Q. I press record button, but the DVR does not start recording, why? A. Please stop record or play before you access these menuQ. Why cannot I access Network Set menu? Q. There is a movement, but the DVR does not start recordingRec rate field/sec Resolution10. Record Time Table Picture quality11.1 About Networks 11. Internet View/Playback Configurations11.2 Network Configurations Page Page Q-SEE Product Warranty Serial Number of Product Purchase Date Distributor Customer Information Card User’s NameMr./Mrs Company Name PostalAddress Postal code Phone Number E-mail Model Number of Product