JA Audio 9902S manual Motor antenna, Manual search, Advanced search

Page 19

FIRST TIME INSTALLATION

Manual search

When you perform a Manual search you first need to enter some parameters for the channel search to work.

The information you need to enter in this menu is available in magazines covering satellite TV reception, on the Internet or from your Service Provider.

Transponder frequency: Specify the frequency in GHz. If you enter the wrong figure(s), erase with the button.

Polarization: Select Horizontal, Vertical, Circular left or Circular right.

Symbol rate (MSym/s): Enter with the numeric buttons. If you enter the wrong figure(s), erase with the button.

FEC: Select “Auto” or any of the preprogrammed values.

Network search: Select “Yes” if you want to search on all trans- ponders connected to a specific network.

Adjust motor: Adjust (if necessary) the motor for the current satellite.

Press OK to start searching for channels.

Advanced search

The information to enter in this menu is available in magazines covering satellite TV reception, or from your Service Provider.

You can use this menu if you are looking for some “special” chan- nels (i.e. non-DVB standard channels) which can only be found when you have entered the necessary settings here.

Transponder frequency: Specify the frequency in GHz.

Polarization: Select Horizontal, Vertical, Circular left or right.

Symbol rate (MSym/s): Enter with the numeric buttons.

FEC: Enter the appropriate Forward Error Correction (FEC) or select AUTO

PID Video: Enter the PID (Packet Identifier) for the video signal.

PID Audio: Enter the PID for the audio signal.

PID PCR: Enter the PID for the PCR (Programme Clock Refer- ence).

Adjust motor: Adjust (if necessary) the motor for the current sat- ellite.

Press OK to start searching for channels.

Motor antenna

In case you have an antenna motor to control your satellite an- tenna you have to make the following settings. If your antenna is prevented from reaching its east/west limit positions, you have to set these limits. See page 47 for instructions.

•From the “Antenna/Satellite selection” menu select line 7 and press OK.

•Select line 5, “Motor antenna” and press OK.

GB 19

Image 19

Contents Mediamaster Page Mediamaster 9902 S ContentsImportant Information in the Event of Service For Your SafetyGeneral Information about the Mediamaster Pad Remote Control+ P Front panel Front and Rear PanelRear panel CA module with its smartcard Viaccess smartcardOnly for services coded with the Viaccess CA system About the Smartcard and CA ModulePreparing the remote control Installation of the MediamasterConnecting the Mediamaster to the dish If your TV has a Scart socket, but your VCR does not Connecting to the TVConnecting a TV and VCR GeneralConnecting a HiFi system Connecting an analogue satellite receiver and a VCRConnecting to the built in phone modem Tuning procedure when RF connections are used Switching on for the first time with Scart connectionsTuning your TV to the Mediamaster Language First Time InstallationGeneral information Welcome menuAntenna/satellite selection RF modulator typeAlternatives 1-6 requires the use of a Universal LNBs Line 1 through 4 on the antenna satel- lite selection menu Antenna adjustment and signal checkLine 5 and 6 on the antenna satellite selection menu Connection of a two port DiSEqC switchLine 7 on the antenna satellite selection Menu One antenna/one LNB configurationMultisatellite/mini DiSEqC Multisatellite/two port DiSEqC Automatic search Connection of a four port DiSEqC switchMultisatellite/four port DiSEqC Channel searchManual search Motor antennaAdvanced search Type of motor Adjust motorPress OK First Time Installation Finishing the first time installation Time adjustmentChannel search progress Programme information Viewing ModeGuide I information buttonSubtitle language List of TV and radio channelsOptions green button Audio languageText button teletext TV releaseRecording from the hard disk to a video recorder Recording on an external analogue Video recorderAbout hard disk recording Hard Disk RecordingRecording menu Different ways of making recordingsLocked functions during recording To watch the pause recording Pause RecordingTo finish this example of a pause recording Normal recording Timer recordingPause during playback of a normal recording To start playback of a recordingPause function Handle Recording menu appearsFast Forward and Rewind of a pause recording in progress Watch the playback at a different speedFind a specific position within a playback Small steps during playbackSlow Motion function Edit function Handle recording List of recordingsPlay Recording information RenameErase Add another recordingSave a recording as Erasable or Permanent Important about editing channels Main MenuTV and radio channels Edit channelsRearrange lists How to give a specific nameCreate list Rename listLock channels Select channelsRename channels To remove channels Rearrange channelsDelete channels Remove channelsUpdate channels via a PC Update channelsFor a fixed antenna System configurationEdit satellites To add a new satelliteWhen your antenna is controlled by a motor TV settings Antenna/Satellite configurationModem Setting Information about the modem Receiver upgradeReinstall Erase hard diskParental control Language preferencesAppearance preferences Repeat playing Recording preferencesMake new recordings Saved pause recordingsType of programme Erase before record hoursSystem information Receiver numberSystem information Following extreme exampleRelease info Conditional AccessViaccess embedded DiagnosticsTimer Smartcard settingsCommon Interface CI Timer setup Important information related to the timer recordingAGC Glossary of TermsProblem Possible causes What to do Problem SolvingFront Panel Display What to do if you can’t solve the problemSecurity information Technical Specifications0226