JA Audio 9902S manual Front Panel Display, What to do if you can’t solve the problem

Page 60

PROBLEM SOLVING

Problem

Possible causes

What to do

The remote control is not working.	Battery exhausted.
	Remote control is incorrectly
	aimed.
	The Mediamaster is in standby
	mode.
	You have set a receiver number
	and then changed batteries in the
	remote control.

Change the batteries (both). Aim the remote control at box. Check that nothing blocks the front panel.

Check if (.) is flashing on the front panel display when you press a button. If not replace the batteries (both).

Press X on your remote control simultaneously, where X is the number you have chosen for the spe- cific receiver. If you don´t remember what number you have used, try 1-4.

You see the on-screen message.	The Mediamaster can’t recognise
	your Smartcard.
Viewing card error.

Check that you are using the proper Smartcard. Check that the Smartcard has been correctly inserted with the gold chip downwards. If the problem persists, you may have a problem with the card.

Contact your dealer or Service Pro- vider.

You have forgotten your secret PIN	Contact your Service Provider.
code.	They will help you set it up again.

CA Module is not working.

CA module is not installed. CA module is not correctly inserted.

Check that the CA module has been correctly inserted.

Contact your dealer or Service Pro- vider.

Black picture.	CA module is inserted but not
	working correctly.

Eject the CA module and reinsert it again.

What to do if you can’t solve the problem

If you have tried all of the actions suggested above, without solving the problem, please contact your dealer or Service Provider.

FRONT PANEL DISPLAY

When power-up, boot version, product family and system software version is shown.

When starting from standby, prod- uct variant and system software version is shown.

Remaining time in percent during the download procedure.

The Mediamaster is in standby mode, and current time is shown.

Channel number in TV mode.

Channel number in radio mode.

RF channel in tuning mode.

In TV mode.

In video mode.

When downloading new software via the air.

When downloading new software via the Serial RS232 socket.

Error messages. For service per- sonnel

Lights when no signal is being re- ceived.

Flashes when pressing a button on the remote control.

GB 60

Image 60

Contents Mediamaster Page Contents Mediamaster 9902 SFor Your Safety Important Information in the Event of ServiceGeneral Information about the Mediamaster Remote Control Pad+ P Front and Rear Panel Front panelRear panel Viaccess smartcard Only for services coded with the Viaccess CA systemAbout the Smartcard and CA Module CA module with its smartcardInstallation of the Mediamaster Preparing the remote controlConnecting the Mediamaster to the dish Connecting to the TV Connecting a TV and VCRGeneral If your TV has a Scart socket, but your VCR does notConnecting an analogue satellite receiver and a VCR Connecting a HiFi systemConnecting to the built in phone modem Switching on for the first time with Scart connections Tuning procedure when RF connections are usedTuning your TV to the Mediamaster First Time Installation General informationWelcome menu LanguageRF modulator type Antenna/satellite selectionAlternatives 1-6 requires the use of a Universal LNBs Antenna adjustment and signal check Line 1 through 4 on the antenna satel- lite selection menuConnection of a two port DiSEqC switch Line 5 and 6 on the antenna satellite selection menuOne antenna/one LNB configuration Line 7 on the antenna satellite selection MenuMultisatellite/mini DiSEqC Multisatellite/two port DiSEqC Connection of a four port DiSEqC switch Multisatellite/four port DiSEqCChannel search Automatic searchMotor antenna Manual searchAdvanced search Adjust motor Type of motorPress OK First Time Installation Time adjustment Finishing the first time installationChannel search progress Viewing Mode Programme informationI information button GuideList of TV and radio channels Options green buttonAudio language Subtitle languageTV release Text button teletextRecording on an external analogue Video recorder Recording from the hard disk to a video recorderHard Disk Recording About hard disk recordingDifferent ways of making recordings Recording menuLocked functions during recording Pause Recording To watch the pause recordingTo finish this example of a pause recording Timer recording Normal recordingTo start playback of a recording Pause functionHandle Recording menu appears Pause during playback of a normal recordingWatch the playback at a different speed Fast Forward and Rewind of a pause recording in progressSmall steps during playback Find a specific position within a playbackSlow Motion function Edit function List of recordings Handle recordingPlay Rename EraseAdd another recording Recording informationSave a recording as Erasable or Permanent Main Menu TV and radio channelsEdit channels Important about editing channelsHow to give a specific name Create listRename list Rearrange listsSelect channels Lock channelsRename channels Rearrange channels Delete channelsRemove channels To remove channelsUpdate channels Update channels via a PCSystem configuration Edit satellitesTo add a new satellite For a fixed antennaWhen your antenna is controlled by a motor Antenna/Satellite configuration TV settingsModem Setting Receiver upgrade ReinstallErase hard disk Information about the modemLanguage preferences Parental controlAppearance preferences Recording preferences Make new recordingsSaved pause recordings Repeat playingErase before record hours Type of programmeReceiver number System informationFollowing extreme example System informationConditional Access Viaccess embeddedDiagnostics Release infoSmartcard settings TimerCommon Interface CI Important information related to the timer recording Timer setupGlossary of Terms AGCProblem Solving Problem Possible causes What to doWhat to do if you can’t solve the problem Front Panel DisplayTechnical Specifications Security information0226