JA Audio 9902S manual Type of motor, Adjust motor, Press OK

Page 20

FIRST TIME INSTALLATION

Type of motor

•Select SATSCAN if it is a Nokia SatScan motor.

•Select DiSEqC in case the motor you use is controlled by DiSEqC commands.

LNB type

•Select Universal, one of the fixed frequencies or enter the LNB frequency with the numeric buttons on the remote control.

LNB offset voltage

If the cable down from the antenna is very long, the voltage at the LNB could be too low to change the polarization. You can in- crease the voltage to the LNB by 0,5 Volt.

Satellite

Select Astra if you have a SatScan motor and Hotbird if you have a DiSEqC motor.

Adjust motor for Astra/Hotbird

To continue the installation you now have to determine the angle to Astra 1/Hotbird. The motor and the antenna must be adjusted towards the Astra 1 satellites on 19.2° East (Hotbird satellites on 13° East) as this is the refer- ence setting. All other preprogrammed satellite positions are oriented relative to Astra 1/Hotbird.

You also have to mount the antenna at a proper place outdoors.

How to do all this, please read the separate fitting in- structions for the SatScan or DiSEqC positioner.

Predefined channel

Select the predefined channel that will give the best Signal qual- ity (SNR) bar indication. Within a few seconds you will get picture from the channel in the background.

Adjust motor

•If necessary, fine tune the motor with the buttons on the

remote control.

As you now have a picture in the background, it is time to per- form a Channel search procedure.

•Press OK......

....and you will get the Channel search menu.

The most common is to start from the “Automatic search” line. (You can always make a Manual or Advanced Search later on.)

•Select the satellite you want to use on the Automatic Search line, for example Astra.

•Press OK......

.......and you get the Antenna adjustment menu.

•If necessary, adjust the motor until the Signal strength (AGC) and the Signal quality (SNR) are optimal. Please note, that this will only affect the present satellite position.

GB 20

Image 20

Contents Mediamaster Page Contents Mediamaster 9902 SGeneral Information about the Mediamaster For Your SafetyImportant Information in the Event of Service + P Remote ControlPad Rear panel Front and Rear PanelFront panel Viaccess smartcard Only for services coded with the Viaccess CA systemAbout the Smartcard and CA Module CA module with its smartcardConnecting the Mediamaster to the dish Installation of the MediamasterPreparing the remote control Connecting to the TV Connecting a TV and VCRGeneral If your TV has a Scart socket, but your VCR does notConnecting to the built in phone modem Connecting an analogue satellite receiver and a VCRConnecting a HiFi system Tuning your TV to the Mediamaster Switching on for the first time with Scart connectionsTuning procedure when RF connections are used First Time Installation General informationWelcome menu LanguageAlternatives 1-6 requires the use of a Universal LNBs RF modulator typeAntenna/satellite selection Antenna adjustment and signal check Line 1 through 4 on the antenna satel- lite selection menuConnection of a two port DiSEqC switch Line 5 and 6 on the antenna satellite selection menuMultisatellite/mini DiSEqC One antenna/one LNB configurationLine 7 on the antenna satellite selection Menu Multisatellite/two port DiSEqC Connection of a four port DiSEqC switch Multisatellite/four port DiSEqCChannel search Automatic searchAdvanced search Motor antennaManual search Press OK Adjust motorType of motor First Time Installation Channel search progress Time adjustmentFinishing the first time installation Viewing Mode Programme informationI information button GuideList of TV and radio channels Options green buttonAudio language Subtitle languageTV release Text button teletextRecording on an external analogue Video recorder Recording from the hard disk to a video recorderHard Disk Recording About hard disk recordingLocked functions during recording Different ways of making recordingsRecording menu Pause Recording To watch the pause recordingTo finish this example of a pause recording Timer recording Normal recordingTo start playback of a recording Pause functionHandle Recording menu appears Pause during playback of a normal recordingWatch the playback at a different speed Fast Forward and Rewind of a pause recording in progressSlow Motion function Small steps during playbackFind a specific position within a playback Edit function Play List of recordingsHandle recording Rename EraseAdd another recording Recording informationSave a recording as Erasable or Permanent Main Menu TV and radio channelsEdit channels Important about editing channelsHow to give a specific name Create listRename list Rearrange listsRename channels Select channelsLock channels Rearrange channels Delete channelsRemove channels To remove channelsUpdate channels Update channels via a PCSystem configuration Edit satellitesTo add a new satellite For a fixed antennaWhen your antenna is controlled by a motor Antenna/Satellite configuration TV settingsModem Setting Receiver upgrade ReinstallErase hard disk Information about the modemLanguage preferences Parental controlAppearance preferences Recording preferences Make new recordingsSaved pause recordings Repeat playingErase before record hours Type of programmeReceiver number System informationFollowing extreme example System informationConditional Access Viaccess embeddedDiagnostics Release infoCommon Interface CI Smartcard settingsTimer Important information related to the timer recording Timer setupGlossary of Terms AGCProblem Solving Problem Possible causes What to doWhat to do if you can’t solve the problem Front Panel DisplayTechnical Specifications Security information0226