JA Audio 9902S manual Problem Solving, Problem Possible causes What to do

Page 59

PROBLEM SOLVING

Problem

Possible causes

What to do

The display on the front panel does

Mains cable is not connected.

not light up/is not lit.

 

Check that the mains cable is plugged into the power socket.

No sound or picture, but the front panel shows the time or - - : - -.

The Mediamaster is in standby mode.

Press the standby button or any number button to bring the Media- master out of standby mode.

No sound or picture.

The satellite dish is not pointing

 

at the satellite.

 

No signal or weak signal.

No sound or picture on horizontal

The LNB is faulty.

 

modulated transponder.

 

Adjust the dish. Check the signal level indicator in one of the channel search submenus.

Check the cable connections, LNB and other equipment connected be- tween the LNB and the receiver, or adjust the dish.

Replace the LNB.

Increase the LNB voltage with 0,5 V from the System Configuration menu if you have a long cable.

Bad picture/blocking error.

The satellite dish is not pointing

Adjust the dish.

 

at the satellite.

 

 

Signal too strong.

Connect a signal attenuator to the

 

 

LNB input.

 

Satellite dish is too small.

Change to a larger dish.

 

LNB noise factor too high.

Change to an LNB with lower noise

 

 

factor.

 

The LNB is faulty.

Change the LNB.

 

 

 

There is no Welcome menu on the screen after you switched on the Mediamaster for the first time.

The system is connected by SCART cables and the TV is not in AV/EXT mode.

The system is connected by RF ca- bles and the TV is not set to the channel tuned for digital satellite TV.

If the system is connected by SCART cables, switch the TV to the appropriate AV input.

If the system is connected by RF cables, switch the TV to the chan- nel for digital satellite TV. If you have not tuned in the TV you may do this first. Please look in the TV manual for instructions. You can also change the RF-channel in the Mediamaster. See TV settings.

There is interference on your digital satellite channels, an existing ter- restrial channel or video signal.

The system is connected by RF ca- bles and the output channel of the Media-master interferes with an existing terrestrial channel or video signal.

Change the Mediamaster output channel to a more suitable channel between 21-69, or connect the sys- tem by SCART cables.

You made a video recording of a dig- ital satellite channel and whole or parts of the programme was not recorded.

The Mediamaster was not left on the appropriate channel.

The system is connected by SCART cables and the VCR is not in AV/EXT mode.

The system is connected by RF ca- bles and the VCR is not set to the channel tuned for digital satellite TV.

If you make a recording of digital satellite TV your Mediamaster has to be left on the channel you want to record.

If the system is connected by SCART cables, switch the VCR to appropriate AV input.

If the system is connected by RF cables, switch the VCR to the chan- nel for digital satellite TV. If you have not tuned in the VCR you may do this first. Please look in the VCR manual for instructions.

GB 59

Page 58 Page 60
Image 59
Page 58 Page 60
Contents Mediamaster Page Mediamaster 9902 S ContentsGeneral Information about the Mediamaster For Your SafetyImportant Information in the Event of Service + P Remote ControlPad Rear panel Front and Rear PanelFront panel CA module with its smartcard Viaccess smartcardOnly for services coded with the Viaccess CA system About the Smartcard and CA ModuleConnecting the Mediamaster to the dish Installation of the MediamasterPreparing the remote control If your TV has a Scart socket, but your VCR does not Connecting to the TVConnecting a TV and VCR GeneralConnecting to the built in phone modem Connecting an analogue satellite receiver and a VCRConnecting a HiFi system Tuning your TV to the Mediamaster Switching on for the first time with Scart connectionsTuning procedure when RF connections are used Language First Time InstallationGeneral information Welcome menuAlternatives 1-6 requires the use of a Universal LNBs RF modulator typeAntenna/satellite selection Line 1 through 4 on the antenna satel- lite selection menu Antenna adjustment and signal checkLine 5 and 6 on the antenna satellite selection menu Connection of a two port DiSEqC switchMultisatellite/mini DiSEqC One antenna/one LNB configurationLine 7 on the antenna satellite selection Menu Multisatellite/two port DiSEqC Automatic search Connection of a four port DiSEqC switchMultisatellite/four port DiSEqC Channel searchAdvanced search Motor antennaManual search Press OK Adjust motorType of motor First Time Installation Channel search progress Time adjustmentFinishing the first time installation Programme information Viewing ModeGuide I information buttonSubtitle language List of TV and radio channelsOptions green button Audio languageText button teletext TV releaseRecording from the hard disk to a video recorder Recording on an external analogue Video recorderAbout hard disk recording Hard Disk RecordingLocked functions during recording Different ways of making recordingsRecording menu To watch the pause recording Pause RecordingTo finish this example of a pause recording Normal recording Timer recordingPause during playback of a normal recording To start playback of a recordingPause function Handle Recording menu appearsFast Forward and Rewind of a pause recording in progress Watch the playback at a different speedSlow Motion function Small steps during playbackFind a specific position within a playback Edit function Play List of recordingsHandle recording Recording information RenameErase Add another recordingSave a recording as Erasable or Permanent Important about editing channels Main MenuTV and radio channels Edit channelsRearrange lists How to give a specific nameCreate list Rename listRename channels Select channelsLock channels To remove channels Rearrange channelsDelete channels Remove channelsUpdate channels via a PC Update channelsFor a fixed antenna System configurationEdit satellites To add a new satelliteWhen your antenna is controlled by a motor TV settings Antenna/Satellite configurationModem Setting Information about the modem Receiver upgradeReinstall Erase hard diskParental control Language preferencesAppearance preferences Repeat playing Recording preferencesMake new recordings Saved pause recordingsType of programme Erase before record hoursSystem information Receiver numberSystem information Following extreme exampleRelease info Conditional AccessViaccess embedded DiagnosticsCommon Interface CI Smartcard settingsTimer Timer setup Important information related to the timer recordingAGC Glossary of TermsProblem Possible causes What to do Problem SolvingFront Panel Display What to do if you can’t solve the problemSecurity information Technical Specifications0226
Top Page Image Contents