Kathrein MSK 24 manual Starting up, Switching on the receiver, Switching off the receiver

Page 15

Starting up

Switching on the receiver

∙Connect the receiver with the battery charger/power supply unit to the mains supply.

∙Turn the on/off switch towards the right.

∙Set the desired volume.

Software V1.0

SN: 000222

ACCU[￿￿￿￿￿]

 

 

CH: .02.

TV

LEV: 48.5dBuV

 

 

 

 

 

The LC display shows the software version and serial number of the MSK 24 for approx. 1 second.

Then the LC display indicates the capacity of the battery for approx. 3 seconds.

One segment is equivalent to approx. 20% of the total capacity (2.8 Ah).

Now apply the receiving signal from the receiver system into the RF input socket.

LC display:

∙channel

∙mode

∙level.

Use the [TV/SAT] button to select the required mode.

Switching off the receiver

Turn the on/off switch towards the left.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Satellite / TV / Radio Test Receiver MSK Page Validity of this manual PrefaceContents Technical Appendix Spectrum measurementParts supplied Explanation of symbolsSafety instructions General NotesHow it operates Overview of functions Block diagram of MSK SAT Technical Data10 V...20 V, max mA LC display Operating and display elementsDisplay elements Connections right sideOverview of the keyboard commands Scart output ConnectionsRF input socket External DC voltage supplySoftware Accu LEV 48.5dBuV Switching on the receiverSwitching off the receiver Starting upSetup menu Setup menuFactory settings Settings in the setup menuMains and battery operation Battery operationMains operation Standard Switch-Over Sat measurementPress 2ndF STD Overview of commands in Entering Frequency SAT Frequency Display and Entering FrequencyPress 1 5 0 8 E Nter LEV dBuV Level MeasurementLevel Overflow and Underflow LEV .dBuVCalling up the Scan function 2ndF Scan Switch over to Scan operationTracking Satellites Change the measuring range of the bar displayTracking for Single Frequencies Overview of commands in TrackingAudio Carrier Frequency Button Frequency in MHz Bandwidth in kHzPress 2ndF SC Press buttons 2ndF LNB LNB Voltage and 22 kHz / 60 Hz Switch-OverOverview of commands in LNB Voltage Example LNB14,0V 150mA LNB voltage ButtonExample LNB14,0V 22kHz 150mA Parity bit DiSEqC Digital Satellite Equipment ControlPress buttons 2ndF SAT-CTRL Overview of commands in Framing ByteHex byte Description Overview of commands in Address ByteOverview of commands in Command Byte Sat measurement Simple Tone Burst DiSEqC Overview of commands in Data ByteOrbit Switch position Data Position Overview of commands in Simple DiSEqCDiSEqC-SIMPLE Tone Burst Enter the letters A...F Button SEC Vario-Satellite Equipment Control2ndF SAT-CTRL Call up the V-SEC menu Enter the figures 0 toOverview of commands in Standard Switch-Over TV TV measurement=BG 2=L 3=DK =I 5=MN 6=M1 Enter the channel Switch over to TV receptionSwitch to special channel Channel Display and Entering ChannelThen 1 7 5 ./S 2 5 Enter LEV.dBuV Level Measurement TVPress buttons 2ndF Level LEV-RANGE2 TV ExampleSC 5.50MHz LEV -13.0dB LEV 58.5dBuV Overview of commands in Measuring Audio Carrier FrequencyAudio Carrier Distance and Level Standard Audio carrier NicamNicam Measuring Audio Bit Error Rates Calling up Measuring Audio Bit Error RatesSC 5.85 MHz BER=2.145E-05 Then 9 9 ./S 2 5 Enter FM measurement2ndF FM Press 2ndF FMFR104,80MHz FM LEV¯¯¯.¯dBuV SAT-Full Spectrum measurementSat Spectrum TV SpectrumTV narrow Overview of commands in TV SpectrumFM Spectrum TV fullMaintenance Changing the batteryCustomer service Signal-to-noise distance Technical Appendix+14.1 dB DiSEqC commands for Kathrein matrices Command set for Kathrein matrix 9xx-seriesCommand set for Kathrein matrix EXR VHF-CCIR UHF-CCIR Channel tablesVHF UHF Channel and frequency table for L standard frequency in MHzIII Channel and frequency table for I standard frequency in MHz Technical Appendix Technical Appendix Technical Appendix Page 936.1997/ZWT/PF Technical data subject to change
Top Page Image Contents