Kathrein MSK 24 manual How it operates

Page 7

How it operates

The MSK 24 is designed as a universal portable test receiver for TV, SAT and FM radio for both battery and mains operation. A built-in lead battery with 2.8 Ah and a plug-in power unit for 230 V AC are included with the receiver.

A microcontroller is responsible for controlling the unit, scanning the keyboard and displaying frequency and level on the LC display. Receiving frequencies are indicated in MHz. Levels are measured with a peak or average value detector and indicated digitally in dBìV or dBmV. Correction values are determined when levels are calibrated for the MSK 24. They are stored in an EEPROM. Precise level measurements can thus be made.

There is a bar display on the front display to help find transmitters. In addition, there is an audio tracking signal to facilitate aligning of the antenna as the display does not have to be observed.

The audio section with its built-in loudspeaker is capable of processing and reproducing various audio frequency satellite signals, audio frequency TV signals complying with the B/G, D/K, I, M1 (Japan) and M/N standards, as well as FM audio. NICAM and AM audio reproduction (L standard) is also possible.

All currently known requirements are covered thanks to an LNB supply voltage of 10-20 V / max. 500 mA with steps of 0.1 V, the superimposition of 22 kHz / 60Hz and the facility of sending DiSEqC or V-SEC commands.

The built-in TFT colour screen allows pictures to be assessed locally.

7

Image 7
Contents Satellite / TV / Radio Test Receiver MSK Page Validity of this manual PrefaceContents Technical Appendix Spectrum measurementParts supplied Explanation of symbolsSafety instructions General NotesHow it operates Overview of functions Block diagram of MSK SAT Technical Data10 V...20 V, max mA LC display Operating and display elementsDisplay elements Connections right sideOverview of the keyboard commands Scart output ConnectionsRF input socket External DC voltage supplySoftware Accu LEV 48.5dBuV Switching on the receiverSwitching off the receiver Starting upSetup menu Setup menuFactory settings Settings in the setup menuBattery operation Mains and battery operationMains operation Sat measurement Standard Switch-OverPress 2ndF STD Frequency Display and Entering Frequency Overview of commands in Entering Frequency SATPress 1 5 0 8 E Nter LEV dBuV Level MeasurementLevel Overflow and Underflow LEV .dBuVCalling up the Scan function 2ndF Scan Switch over to Scan operationTracking Satellites Change the measuring range of the bar displayTracking for Single Frequencies Overview of commands in TrackingButton Frequency in MHz Bandwidth in kHz Audio Carrier FrequencyPress 2ndF SC Press buttons 2ndF LNB LNB Voltage and 22 kHz / 60 Hz Switch-OverOverview of commands in LNB Voltage Example LNB14,0V 150mA LNB voltage ButtonExample LNB14,0V 22kHz 150mA Parity bit DiSEqC Digital Satellite Equipment ControlPress buttons 2ndF SAT-CTRL Overview of commands in Framing ByteHex byte Description Overview of commands in Address ByteOverview of commands in Command Byte Sat measurement Simple Tone Burst DiSEqC Overview of commands in Data ByteOrbit Switch position Data Position Overview of commands in Simple DiSEqCDiSEqC-SIMPLE Tone Burst Enter the letters A...F Button SEC Vario-Satellite Equipment Control2ndF SAT-CTRL Call up the V-SEC menu Enter the figures 0 toTV measurement Overview of commands in Standard Switch-Over TV=BG 2=L 3=DK =I 5=MN 6=M1 Enter the channel Switch over to TV receptionSwitch to special channel Channel Display and Entering ChannelThen 1 7 5 ./S 2 5 Enter LEV.dBuV Level Measurement TVPress buttons 2ndF Level LEV-RANGE2 TV ExampleSC 5.50MHz LEV -13.0dB LEV 58.5dBuV Overview of commands in Measuring Audio Carrier FrequencyAudio Carrier Distance and Level Standard Audio carrier NicamCalling up Measuring Audio Bit Error Rates Nicam Measuring Audio Bit Error RatesSC 5.85 MHz BER=2.145E-05 Then 9 9 ./S 2 5 Enter FM measurement2ndF FM Press 2ndF FMFR104,80MHz FM LEV¯¯¯.¯dBuV SAT-Full Spectrum measurementSat Spectrum TV SpectrumTV narrow Overview of commands in TV SpectrumFM Spectrum TV fullChanging the battery MaintenanceCustomer service Technical Appendix Signal-to-noise distance+14.1 dB Command set for Kathrein matrix 9xx-series DiSEqC commands for Kathrein matricesCommand set for Kathrein matrix EXR VHF-CCIR UHF-CCIR Channel tablesVHF UHF Channel and frequency table for L standard frequency in MHzIII Channel and frequency table for I standard frequency in MHz Technical Appendix Technical Appendix Technical Appendix Page 936.1997/ZWT/PF Technical data subject to change