Kathrein MSK 24 manual Frequency Display and Entering Frequency, Press 1 5 0 8 E Nter

Page 19

Sat measurement

Frequency Display and Entering Frequency

To measure the level of a received signal, you must first enter the desired frequency. The LC display shows the frequency and the measured level. You can enter frequency values from 920 MHz to 2150 MHz in steps of 100 kHz.

Overview of commands in Entering Frequency (SAT)

ë


FR:1288.0MHz	SAT
LEV: 66.5dBuV

Example

[SAT/TV] Switch over to SAT reception

[0]...[9] Enter frequency

[+][-]You can alter frequency in steps of 100 kHz

[ENTER] Confirm entry

LC display:

∙Frequency: 1288 MHz

∙Mode: SAT

∙Level: 66.5 dBìV

Enter frequency 1508 MHz

Press [1] [5] [0] [8] [E NTER]

LC display:


FR:1508.0MHz	SAT
LEV: 86.5dBuV

∙Frequency: 1508 MHz

∙Mode: SAT

∙Level: 86.5 dBìV

Note

+

A + or – in the display means that MSK 24 has not been tuned in exactly to the desired carrier. Use the [+] and [-]buttons to adjust the frequency for the best possible reception. When a vertical line appears in the display, the frequency has the best possible setting.

Press [ENTER] to complete the frequency entry.

The last frequency setting is retained even when the MSK 24 is switched off provided it was made using "numerical entries" and concluded with "MHz".

19

Image 19

Contents Satellite / TV / Radio Test Receiver MSK Page Validity of this manual PrefaceContents Technical Appendix Spectrum measurementParts supplied Explanation of symbolsSafety instructions General NotesHow it operates Overview of functions Block diagram of MSK SAT Technical Data10 V...20 V, max mA LC display Operating and display elementsDisplay elements Connections right sideOverview of the keyboard commands Scart output ConnectionsRF input socket External DC voltage supplySoftware Accu LEV 48.5dBuV Switching on the receiverSwitching off the receiver Starting upSetup menu Setup menuFactory settings Settings in the setup menuBattery operation Mains and battery operationMains operation Sat measurement Standard Switch-OverPress 2ndF STD Frequency Display and Entering Frequency Overview of commands in Entering Frequency SATPress 1 5 0 8 E Nter LEV dBuV Level MeasurementLevel Overflow and Underflow LEV .dBuVCalling up the Scan function 2ndF Scan Switch over to Scan operationTracking Satellites Change the measuring range of the bar displayTracking for Single Frequencies Overview of commands in TrackingButton Frequency in MHz Bandwidth in kHz Audio Carrier FrequencyPress 2ndF SC Press buttons 2ndF LNB LNB Voltage and 22 kHz / 60 Hz Switch-OverOverview of commands in LNB Voltage Example LNB14,0V 150mA LNB voltage ButtonExample LNB14,0V 22kHz 150mA Parity bit DiSEqC Digital Satellite Equipment ControlPress buttons 2ndF SAT-CTRL Overview of commands in Framing ByteHex byte Description Overview of commands in Address ByteOverview of commands in Command Byte Sat measurement Simple Tone Burst DiSEqC Overview of commands in Data ByteOrbit Switch position Data Position Overview of commands in Simple DiSEqCDiSEqC-SIMPLE Tone Burst Enter the letters A...F Button SEC Vario-Satellite Equipment Control2ndF SAT-CTRL Call up the V-SEC menu Enter the figures 0 toTV measurement Overview of commands in Standard Switch-Over TV=BG 2=L 3=DK =I 5=MN 6=M1 Enter the channel Switch over to TV receptionSwitch to special channel Channel Display and Entering ChannelThen 1 7 5 ./S 2 5 Enter LEV.dBuV Level Measurement TVPress buttons 2ndF Level LEV-RANGE2 TV ExampleSC 5.50MHz LEV -13.0dB LEV 58.5dBuV Overview of commands in Measuring Audio Carrier FrequencyAudio Carrier Distance and Level Standard Audio carrier NicamCalling up Measuring Audio Bit Error Rates Nicam Measuring Audio Bit Error RatesSC 5.85 MHz BER=2.145E-05 Then 9 9 ./S 2 5 Enter FM measurement2ndF FM Press 2ndF FMFR104,80MHz FM LEV¯¯¯.¯dBuV SAT-Full Spectrum measurementSat Spectrum TV SpectrumTV narrow Overview of commands in TV SpectrumFM Spectrum TV fullChanging the battery MaintenanceCustomer service Technical Appendix Signal-to-noise distance+14.1 dB Command set for Kathrein matrix 9xx-series DiSEqC commands for Kathrein matricesCommand set for Kathrein matrix EXR VHF-CCIR UHF-CCIR Channel tablesVHF UHF Channel and frequency table for L standard frequency in MHzIII Channel and frequency table for I standard frequency in MHz Technical Appendix Technical Appendix Technical Appendix Page 936.1997/ZWT/PF Technical data subject to change