Kathrein MSK 24 manual Sat measurement, Standard Switch-Over, Press 2ndF STD

Page 18

Sat measurement

Standard Switch-Over

In the SAT mode the MSK 24 can be set to receive the following types of signal:

∙analogue and

∙digital (DVB).

Overview of commands in Standard Switch-Over in SAT

[2ndF] [STD] Call up standard switch-over menu:

ë [1]...[2] Select the standard 1 = analogue

2 = digital (DVB)

Example

	0	Call up digital (DVB) standard:
		Press [2ndF] [STD]

		LC display:
		∙	1	= analogue standard
	1=ANALOG
	2=DIGITAL(DVB)	∙	2	= digital (DVB) standard

Standard menu


FR:1288.0MHz	SAT
LEV: 66.5dBuV	D

If you press button [2], you will leave the standard menu and the receiver will be set to DVB measurement.

A "D" appears in the display.

Display for DVB measurement

18

Image 18

Contents Satellite / TV / Radio Test Receiver MSK Page Preface Validity of this manualContents Spectrum measurement Technical AppendixGeneral Notes Explanation of symbolsSafety instructions Parts suppliedHow it operates Overview of functions Block diagram of MSK Technical Data SAT10 V...20 V, max mA Connections right side Operating and display elementsDisplay elements LC displayOverview of the keyboard commands External DC voltage supply ConnectionsRF input socket Scart outputStarting up Switching on the receiverSwitching off the receiver Software Accu LEV 48.5dBuVSettings in the setup menu Setup menuFactory settings Setup menuMains and battery operation Battery operationMains operation Standard Switch-Over Sat measurementPress 2ndF STD Overview of commands in Entering Frequency SAT Frequency Display and Entering FrequencyPress 1 5 0 8 E Nter LEV .dBuV Level MeasurementLevel Overflow and Underflow LEV dBuVChange the measuring range of the bar display 2ndF Scan Switch over to Scan operationTracking Satellites Calling up the Scan functionOverview of commands in Tracking Tracking for Single FrequenciesAudio Carrier Frequency Button Frequency in MHz Bandwidth in kHzPress 2ndF SC LNB voltage Button LNB Voltage and 22 kHz / 60 Hz Switch-OverOverview of commands in LNB Voltage Example LNB14,0V 150mA Press buttons 2ndF LNBExample LNB14,0V 22kHz 150mA DiSEqC Digital Satellite Equipment Control Parity bitOverview of commands in Framing Byte Press buttons 2ndF SAT-CTRLOverview of commands in Address Byte Hex byte DescriptionOverview of commands in Command Byte Sat measurement Overview of commands in Simple DiSEqC Overview of commands in Data ByteOrbit Switch position Data Position Simple Tone Burst DiSEqCDiSEqC-SIMPLE Tone Burst Enter the figures 0 to SEC Vario-Satellite Equipment Control2ndF SAT-CTRL Call up the V-SEC menu Enter the letters A...F ButtonOverview of commands in Standard Switch-Over TV TV measurement=BG 2=L 3=DK =I 5=MN 6=M1 Channel Display and Entering Channel Switch over to TV receptionSwitch to special channel Enter the channelThen 1 7 5 ./S 2 5 Enter Level Measurement TV LEV.dBuVLEV-RANGE2 TV Example Press buttons 2ndF LevelStandard Audio carrier Nicam Overview of commands in Measuring Audio Carrier FrequencyAudio Carrier Distance and Level SC 5.50MHz LEV -13.0dB LEV 58.5dBuVNicam Measuring Audio Bit Error Rates Calling up Measuring Audio Bit Error RatesSC 5.85 MHz BER=2.145E-05 Press 2ndF FM FM measurement2ndF FM Then 9 9 ./S 2 5 EnterFR104,80MHz FM LEV¯¯¯.¯dBuV TV Spectrum Spectrum measurementSat Spectrum SAT-FullTV full Overview of commands in TV SpectrumFM Spectrum TV narrowMaintenance Changing the batteryCustomer service Signal-to-noise distance Technical Appendix+14.1 dB DiSEqC commands for Kathrein matrices Command set for Kathrein matrix 9xx-seriesCommand set for Kathrein matrix EXR Channel tables VHF-CCIR UHF-CCIRChannel and frequency table for L standard frequency in MHz VHF UHFIII Channel and frequency table for I standard frequency in MHz Technical Appendix Technical Appendix Technical Appendix Page 936.1997/ZWT/PF Technical data subject to change