Kathrein cap910 Installation of the UFS 940SW, Selection of a Suitable Installation Location

Page 18

INSTALLATION AND CONNECTION

INSTALLATION OF THE UFS 940SW

SELECTION OF A SUITABLE INSTALLATION LOCATION

Note: When choosing the installation location, bear in mind that the rear of the unit should always be accessible. The UFS 940sw is equipped with a power saving circuit and a separate infrared transmitter, which means that the unit does not need to be placed where it is visible. You can therefore fit the UFS 940sw out of sight in any location, e.g. on cupboard walls, side walls or the base of storage compartments.

The four screw sockets provided (see diagram on the next page) allow you to install the receiver not only resting on a shelf but also to fix it there or in other positions.

In addition, the following points should be taken into account:

The wall thickness at the installation location must be at least 15 mm, as otherwise the screws will break through on the other side or damage the surface

Ensure that the cupboard or storage compartment in which the unit is to be housed is adequately ventilated to prevent a build up of heat. Carpet-covered walls are unsuitable for installation

Take care when tightening the screws not to damage any cables etc. behind or in the wall

The receiver is designed exclusively for installation in dry, interior locations. The installation location must be protected against moisture

The cable lengths must be taken into account when choosing the installation location

The connecting cables must be provided with strain reliefs

Ventilation:

The heat generated within the receiver can be dissipated from the following sides of the casing: bottom, left, right and top. When selecting the installation location, make sure that these sides are not obstructed or covered. If the unit is operated continuously with insufficient ventilation, this can negatively affect the length of its working life!

Maintain a clearance of at least 20 cm above or below the unit, 2 cm to either side and 5 cm behind it, to allow unobstructed dissipation of the heat generated.

20 cm

 

Minimum

 

 

 

 

5

cm

cm

 

clearance

 

 

2

 

 

 

 

5

cm

 

 

 

 

2

cm

The unit monitors its temperature in operation. Premature failure of the unit due to continuous operation at temperatures higher than the recommended operating temperature as a result of insufficient ventilation does not constitute grounds for a claim under warranty/guarantee.

18

Image 18
Contents CAP General Company Address and Accredited RepresentativeMobiset 4 CAP 910 Components / Scope of Delivery Product PackageContents Installation Manual Contents Operating Manual Proper USE Proper USE USE for the Intended PurposeSafety Instructions Important Notes Essential informationAdhesive sealant Power supply, fusing Road Traffic Licensing Regulations StVZOChecks before commencing a journey Required Tools and Equipment Installation and ConnectionSelecting the Installation Location Unpacking and PreparationDirection of travel Installation Steps Figure C Not included Installation of Turntable Variant with Cable Gland Underneath the TurntableFigure E1 Master coaxial cable marked red Version with External Cable Gland FIG. F Installation and Connection Installation of the UFS 940SW Selection of a Suitable Installation LocationPreparations Important Instructions for Installation Rear of the receiver Front of the receiver Installation Laying Cables and Connecting the Turntable Installation and Connection Connection Example for 12 V Battery Connection Receiver. There is no restriction onReception Range / Footprint Dismantling Address of the Service CentreDismantling for Servicing ESCSafety Instructions Manual Lowering to Park PositionManual Lowering Technical Specifications Direction of travelComposition/data on components Sikaflex 291 Safety Data SheetMaterials/preparation and company designation Potential hazardsHandling and storage Measures for fire fightingMeasures if inadvertently released Exposure limitation and personal protective equipmentPhysical and chemical characteristics Stability and reactivityDisposal instructions Toxicology data SensitisationEcological data Transport dataOther data Sikaflex 291 Technical Data Sheet Sikaflex-291 IkaflexChemical Stability CAP CAP 910 Operating ManualImportant Information for CAP 910 Before Setup Remote ControlFirst Installation Hdmi Video System Local time offset UTC Automatic clock change summer/winter timeCalling UP the CAP Menu CAP Menu Turntable Antenna SettingsResetting the CAP System Turntable Antenna Reset All satellite positions found by a search will be deletedInputting the CAP GPS Position To Move the Antenna ManuallyElevation Stop on Signal LNB TILT/SKEWMove to the Azimuth Rotate the Antenna Elevation Border and Elevation Offset CAP SettingsMove CAP to Park Position Search SpeedRestore Factory Settings Countdown for the Search StartAlignment Satellite Search Channel Satellite SELECTION/PROGRAMMING the Timer Channel Selection from the Channel ListTimer Programming Channel Selection from the Channel List Sorted by SatelliteChange of Location Change of Location Park Parking the TurntableSpecial Messages from the Turntable System Protection MessagesSpecial Messages from the Turntable Messages Arising from Software Problems Further MessagesTimer function is currently not yet available in CAP mode Declaration of Conformity Disposal Instructions Spent batteries are special waste