Kathrein cap910 manual Important Information for CAP 910 Before Setup, Remote Control

Page 39

IMPORTANT INFORMATION FOR CAP 910 BEFORE SETUP

This section of the UFS 940sw operating manual for the turntable assumes that the UFS 940sw and the turntable have been properly installed and connected, as described in the installation and operating manuals.

If you have not yet done so, read the safety instructions at the beginning of the UFS 940sw operating manual and follow them when handling the UFS 940sw and the turntable unit.

Before setting up your satellite system, make sure that the location allows a free view to the satellite positions to the South and is not shadowed by trees or other obstructions. This will save you time and effort.

So as to avoid overheating the turntable motors, do not operate the motors continuously for longer than 20 minutes.

None of the search procedures initiated by the CAP 910 will require as much as 20 minutes operation. Only repeated unsuccessful search procedures or manual overrides by the user can cause this limit to be exceeded.

As soon as the ignition signal is no longer present at the turntable, if the receiver is switched on the turntable will be supplied with a +12 V power supply and may automatically move to the last known satellite position. Therefore switch your receiver on only if you wish to use your CAP 910.

Reception

reception No

REMOTE CONTROL

All settings on the UFS 940 are made using the remote!

39

Image 39
Contents CAP Company Address and Accredited Representative GeneralProduct Package Mobiset 4 CAP 910 Components / Scope of DeliveryContents Installation Manual Contents Operating Manual Proper USE USE for the Intended Purpose Proper USESafety Instructions Important Notes Essential informationAdhesive sealant Road Traffic Licensing Regulations StVZO Power supply, fusingChecks before commencing a journey Unpacking and Preparation Installation and ConnectionSelecting the Installation Location Required Tools and EquipmentDirection of travel Installation Steps Figure C Not included Variant with Cable Gland Underneath the Turntable Installation of TurntableFigure E1 Master coaxial cable marked red Version with External Cable Gland FIG. F Installation and Connection Selection of a Suitable Installation Location Installation of the UFS 940SWPreparations Important Instructions for Installation Rear of the receiver Front of the receiver Installation Laying Cables and Connecting the Turntable Installation and Connection Receiver. There is no restriction on Connection Example for 12 V Battery ConnectionReception Range / Footprint ESC Address of the Service CentreDismantling for Servicing DismantlingManual Lowering to Park Position Safety InstructionsManual Lowering Direction of travel Technical SpecificationsPotential hazards Sikaflex 291 Safety Data SheetMaterials/preparation and company designation Composition/data on componentsExposure limitation and personal protective equipment Measures for fire fightingMeasures if inadvertently released Handling and storageStability and reactivity Physical and chemical characteristicsTransport data Toxicology data SensitisationEcological data Disposal instructionsOther data Sikaflex-291 Ikaflex Sikaflex 291 Technical Data SheetChemical Stability CAP 910 Operating Manual CAPRemote Control Important Information for CAP 910 Before SetupFirst Installation Hdmi Video System Automatic clock change summer/winter time Local time offset UTCAll satellite positions found by a search will be deleted CAP Menu Turntable Antenna SettingsResetting the CAP System Turntable Antenna Reset Calling UP the CAP MenuInputting the CAP GPS Position To Move the Antenna ManuallyElevation Stop on Signal LNB TILT/SKEWMove to the Azimuth Rotate the Antenna Search Speed CAP SettingsMove CAP to Park Position Elevation Border and Elevation OffsetCountdown for the Search Start Restore Factory SettingsAlignment Satellite Search Channel Selection from the Channel List Channel Satellite SELECTION/PROGRAMMING the TimerChannel Selection from the Channel List Sorted by Satellite Timer ProgrammingChange of Location Change of Location Parking the Turntable ParkSystem Protection Messages Special Messages from the TurntableSpecial Messages from the Turntable Further Messages Messages Arising from Software ProblemsTimer function is currently not yet available in CAP mode Declaration of Conformity Spent batteries are special waste Disposal Instructions