Kathrein cap910 manual Toxicology data Sensitisation, Ecological data, Disposal instructions

Page 34
Hazardous to health

SIKAFLEX® 291 SAFETY DATA SHEET

11. Toxicology data Sensitisation

Sensitisation/allergic reactions may occur.

Sensitive individuals may exhibit allergic reactions even at very low concentrations.

Experience of human exposure

 

On skin contact:

May lead to irritation

On eye contact:

May lead to irritation

On being breathed in:

May lead to irritation

On being swallowed:

May lead to health problems

12. Ecological data

Additional instructions

Do not allow to run into the drains, bodies of water or the ground.

13. Disposal instructions

Product

Recommendations

In accordance with the applicable waste labelling regulations, waste should be classified by its origin. Therefore a unique waste code number cannot be assigned.

Packaging Recommendations

Packaging that is empty of residues should be sent for recycling. Packaging that contains residues of hazardous substances or which is contaminated with hazardous substances, and any packaging that is not empty of residues should be disposed of as the product, correctly and without creating pollution.

If the last contents makes it necessary, packaging that is empty of residues must be pre-treated for disposal (e.g. washed out, neutralised, cured, shaken out).

14. Transport data

ADR/RID

Further data

Not hazardous cargo.

IMO/IMDG

Marine pollutant: no

Further data

Not hazardous cargo.

IATA/ICAO

Further data

Not hazardous cargo.

15. Regulations

Identification in accordance with EC directives

The product should be classified and identified in accordance with EC directives/national statute law.

Component(s) to be labelled as hazardous content: 4.4’ methylene-diphenyl-diisocyanate Hazard symbols

Xn

34

Image 34
Contents CAP General Company Address and Accredited RepresentativeMobiset 4 CAP 910 Components / Scope of Delivery Product PackageContents Installation Manual Contents Operating Manual Proper USE Proper USE USE for the Intended PurposeEssential information Safety Instructions Important NotesAdhesive sealant Power supply, fusing Road Traffic Licensing Regulations StVZOChecks before commencing a journey Required Tools and Equipment Installation and ConnectionSelecting the Installation Location Unpacking and PreparationDirection of travel Installation Steps Figure C Not included Installation of Turntable Variant with Cable Gland Underneath the TurntableFigure E1 Master coaxial cable marked red Version with External Cable Gland FIG. F Installation and Connection Installation of the UFS 940SW Selection of a Suitable Installation LocationPreparations Important Instructions for Installation Rear of the receiver Front of the receiver Installation Laying Cables and Connecting the Turntable Installation and Connection Connection Example for 12 V Battery Connection Receiver. There is no restriction onReception Range / Footprint Dismantling Address of the Service CentreDismantling for Servicing ESCSafety Instructions Manual Lowering to Park PositionManual Lowering Technical Specifications Direction of travelComposition/data on components Sikaflex 291 Safety Data SheetMaterials/preparation and company designation Potential hazardsHandling and storage Measures for fire fightingMeasures if inadvertently released Exposure limitation and personal protective equipmentPhysical and chemical characteristics Stability and reactivityDisposal instructions Toxicology data SensitisationEcological data Transport dataOther data Sikaflex 291 Technical Data Sheet Sikaflex-291 IkaflexChemical Stability CAP CAP 910 Operating ManualImportant Information for CAP 910 Before Setup Remote ControlFirst Installation Hdmi Video System Local time offset UTC Automatic clock change summer/winter timeCalling UP the CAP Menu CAP Menu Turntable Antenna SettingsResetting the CAP System Turntable Antenna Reset All satellite positions found by a search will be deletedTo Move the Antenna Manually Inputting the CAP GPS PositionElevation LNB TILT/SKEW Stop on SignalMove to the Azimuth Rotate the Antenna Elevation Border and Elevation Offset CAP SettingsMove CAP to Park Position Search SpeedRestore Factory Settings Countdown for the Search StartAlignment Satellite Search Channel Satellite SELECTION/PROGRAMMING the Timer Channel Selection from the Channel ListTimer Programming Channel Selection from the Channel List Sorted by SatelliteChange of Location Change of Location Park Parking the TurntableSpecial Messages from the Turntable System Protection MessagesSpecial Messages from the Turntable Messages Arising from Software Problems Further MessagesTimer function is currently not yet available in CAP mode Declaration of Conformity Disposal Instructions Spent batteries are special waste