Kathrein cap910 manual Proper USE USE for the Intended Purpose

Page 6

PROPER USE

PROPER USE (USE FOR THE INTENDED PURPOSE)

The MobiSet 4 digital CAP 910 is designed to receive digital TV and radio channels via satellite. The automatic positioner is intended to be used as a turntable for the Kathrein satellite dish.

The turntable can be used to receive digital TV and radio signals in the frequency range from 10.70 to 12.75 GHz; the antenna cannot receive terrestrial signals (e.g. DVB-T).

The turntable can only be used in conjunction with the UFS 940sw/740sw DVB-S receiver.

In conjunction with these receivers, the turntable provides fully automatic alignment of the satellite dish to receive digital satellite signals. The turntable is designed for use on stationary caravans or motor homes.

Any use other than that specified above will invalidate the warranty or guarantee.

The following circumstances result in the loss of all warranty and liability claims towards the manufacturer:

Improper installation

Use of non-specified mounting materials, which cannot guarantee the mechanical reliability of the antenna system

Impermissible use, e.g. use of the reflector dish for storage

Structural changes or interference with the components and mounting accessories in the set, which could endanger both the mechanical and functional reliability

Improper or forcible opening of the components

Use of cleaners containing solvents, such as acetone, nitro-cellulose thinners, petrol etc.

Failure to observe installation and safety instructions in this manual

Note: The maximum permissible speed for vehicles with a CAP 910 receiver unit mounted on the roof is 130 km/h. Before commencing a journey, the antenna must always be lowered into horizontal position (park position).

The turntable may be operated in an ambient temperature range of -20 °C to +45 °C. Operating the system outside this range may result in malfunctions or damage to the system. When choosing the location for installation or raising the UFS 940sw, ensure there is adequate ventilation.

The system may only be installed by qualified specialist personnel!

To prevent hazards during installation, operation or when driving on public highways, the instructions and information in this manual must be strictly adhered to. Proper installation and connection of the system are pre-requisites for conformity with the corresponding standards.

This is documented in advance by the CE mark and the declaration of conformity in the appendix to this manual.

6

Image 6
Contents CAP General Company Address and Accredited RepresentativeMobiset 4 CAP 910 Components / Scope of Delivery Product PackageContents Installation Manual Contents Operating Manual Proper USE Proper USE USE for the Intended PurposeSafety Instructions Important Notes Essential informationAdhesive sealant Power supply, fusing Road Traffic Licensing Regulations StVZOChecks before commencing a journey Required Tools and Equipment Installation and ConnectionSelecting the Installation Location Unpacking and PreparationDirection of travel Installation Steps Figure C Not included Installation of Turntable Variant with Cable Gland Underneath the TurntableFigure E1 Master coaxial cable marked red Version with External Cable Gland FIG. F Installation and Connection Installation of the UFS 940SW Selection of a Suitable Installation LocationPreparations Important Instructions for Installation Rear of the receiver Front of the receiver Installation Laying Cables and Connecting the Turntable Installation and Connection Connection Example for 12 V Battery Connection Receiver. There is no restriction onReception Range / Footprint Dismantling Address of the Service CentreDismantling for Servicing ESCSafety Instructions Manual Lowering to Park PositionManual Lowering Technical Specifications Direction of travelComposition/data on components Sikaflex 291 Safety Data SheetMaterials/preparation and company designation Potential hazardsHandling and storage Measures for fire fightingMeasures if inadvertently released Exposure limitation and personal protective equipmentPhysical and chemical characteristics Stability and reactivityDisposal instructions Toxicology data SensitisationEcological data Transport dataOther data Sikaflex 291 Technical Data Sheet Sikaflex-291 IkaflexChemical Stability CAP CAP 910 Operating ManualImportant Information for CAP 910 Before Setup Remote ControlFirst Installation Hdmi Video System Local time offset UTC Automatic clock change summer/winter timeCalling UP the CAP Menu CAP Menu Turntable Antenna SettingsResetting the CAP System Turntable Antenna Reset All satellite positions found by a search will be deletedInputting the CAP GPS Position To Move the Antenna ManuallyElevation Stop on Signal LNB TILT/SKEWMove to the Azimuth Rotate the Antenna Elevation Border and Elevation Offset CAP SettingsMove CAP to Park Position Search SpeedRestore Factory Settings Countdown for the Search StartAlignment Satellite Search Channel Satellite SELECTION/PROGRAMMING the Timer Channel Selection from the Channel ListTimer Programming Channel Selection from the Channel List Sorted by SatelliteChange of Location Change of Location Park Parking the TurntableSpecial Messages from the Turntable System Protection MessagesSpecial Messages from the Turntable Messages Arising from Software Problems Further MessagesTimer function is currently not yet available in CAP mode Declaration of Conformity Disposal Instructions Spent batteries are special waste