Kathrein UFD 170 manual Antenna Setup

Page 53

Installation Menu

Antenna Setup

This setting is not necessary for caravan operation.

This menu is exclusively intended for service purposes and be used to align the antenna in an emergency, if no measuring instruments are

available. The key activates a search tone, the pitch of which cor- responds to the signal strength - the higher the sound, the better the signal.

In this menu, you can use the  keys to call up the individual menu options and make the settings with the keys.

The fi rst line is used to specify the satellite and the second line to specify the transponder.

In the small box immediately to the right, the fi rst line shows the polarisation of the received signal and the second line shows the transmitted symbol rate.

The bars provide information about the strength (relative level) of the signal and its quality. However, this information cannot be used to draw any conclusions about the quality of the antenna system.

Operation with antenna rotor / positioner (DiSEqC™ 1.2 )

This setting is not necessary for caravan operation.

For operation with a rotor (DiSEqC™1.2), select “Motor/Goto 0°” “On” in the third line.

In the next line “Move/Save”, you can align the antenna to the East or the West. The optimum setup can be viewed in the “Level” bar chart.

In the “Set Limit Value” line, you can set the outermost aiming point (limited by a wall or another obstruction) in a Westerly or Easterly direction.

Always read the operating manual supplied by the rotor manufacturer (this applies in particular to settings different from those described above).

53

Image 53
Contents UFD Page Foreword Contents Setting System Parameters Password and Child ProtectionInstallation Menu Connection DiagramContents Power supply cable Safety Instructions and Important InformationConnecting the Unit Connection and SetupReceiving System Presets SAT-IF ConnectionTV Connection Inserting Batteries in the Remote ControlAudio Connection Dolby ConnectionFront View Rear View Controls, Displays and ConnectionsFront View Exit Remote Control Function KeysRemote control instruction sets Important information on the remote controlLanguage Selection Operating InstructionsMenu Concept Key Alphanumeric Assignment of Remote Control Number KeysMenu Structure Getting Started Initial SetupImportant Information Initial Setup Time/Timer section Receiver Factory Satellite SettingHelp Function On Screen Display OSDGeneral Channel Message Radio Error MessageTV / Radio Channel Message Video Text Reception Status Programme SelectionSelecting a TV or Radio Programme TV / Radio Channel List Selecting TV/Radio Programmes by Number Switching from a TV Programme to a Radio ProgrammeInserting the Smartcard and the CA Module Common InterfaceMenu language Information for Conax, SECA, Viaccess and CryptoWorks Users Timer Settings VPS Signal Stereo and Two-Channel Sound Playback Audio SettingsSetting the Volume Your Dolby Digital system Turning Off the Sound MuteEPG Electronic Programme Guide Programme Overview EPGEPG Timer Programming Selecting the Last Programmes Received Managing Channel List/ChannelsFavourite Channel Setting Up a Favourite ChannelRenaming the Favourite Lists Undoing Favourite Selection Selecting a Favourite Channel from a Favourite ListChannel List Mode Favourite, Satellite, Alphabetical Complete Channel List Sorting Channels Deleting Channels Adding Channels Manually Adding/Deleting Satellites Setting Up SatellitesDeleting Satellites Setting the Password and Child Protection Password and Child ProtectionPassword Factory Setting Child Protection Locking a Channel Password and Child Protection System Information Setting System ParametersChild Protection Picture Format Local Time/TimerTV Type Mode ScreenOpening the Installation Menu Installation MenuLNB Configuration Oscillator FrequencyStandby OperationDiSEqC2 Setting DiSEqC1 SettingAntenna Setup Satellite Search Changing/Searching for/Deleting Transponders DiSEqCTM UFO Setup Tone Burst and DiSEqCTM Signal KHz SignalDiSEqCTM DiSEqCTM RepeatReset does not delete the pre-programming Factory SettingsAfter resetting, you may need to make all settings again Remote FrequencySoftware and Programme List Update During the download, Please wait fl ashes on the screen Connection between Type of connection Connection DiagramControl Cable SAT-ZF ConnectionOn-Board Network Connection Initial Setup Information Important Information on the Turntable before SetupAlignment Satellite Search Manual Correction Alignment Satellite Search Change of Location Reset Reset/ParkPark Satellite Lost / Limit Reached Special Messages for TurntableSystem Protection Messages Using the  key Turntable Unit Software Download Turntable Unit Software Download Manual Lowering to Park Position Safety InstructionsManual Retraction Service DVB GlossaryDiSEqC components Brief Technical GlossaryDolby Digital Eb/No ratioProgramme package Symbol rateTransponder Video bit rate936.2705/B/0505/ZWT Subject to technical changes