Kathrein UFD 170 manual Safety Instructions and Important Information, Power supply cable

Page 7

Safety Instructions and Important Information

This page contains important information on the operation, installation location and connection of the unit.

Read these instructions carefully before setting up the unit.

Power supply cable

Make sure that the power supply cable is not damaged. Units with a damaged power supply cable must be disconnected from the power supply and repaired by a qualifi ed engineer before setup.

Risk of death due to electric shock.

DANGER! Fuse in cable and receiver

Removing or bridging the fuse in the cable or the receiver is prohibited.

A defective fuse should only be replaced by a fuse with the same rated value !

Risk of fi re due to short circuit.

Cleaning

Disconnect the unit from the power supply before cleaning it. Only use a dry cloth for cleaning, and only clean the outer surface. Never open the unit.

Touching the parts inside the unit carries a risk of death due to electric shock.

Playing children

Make sure that children do not push any objects into the ventilation slots.

Risk of death due to electric shock.

Earthing

The antenna system must be earthed as specifi ed or equipotentially bonded. The requirements of EN 60728/11 and any national regulations must be met.

Danger due to surge voltages, lightning strikes.

WARNING! Mains voltage

Only operate the unit at the specifi ed mains voltage (indicated on the rear of the unit or on the external power pack)! The unit may only be connected to the mains and turned on once it has been connected to the antenna and to the TV set or the cable network and PC.

If the mains voltage is too high, there is a risk of fi re.

Vehicle height

Risk of accidents due to exceeding normal vehicle height by failure to lower antenna.

The driver is responsible for the condition of the superstructure and external fi ttings

Failure to lower the antenna can result in severe damage to the antenna and to the vehicle.

Repairs

Ensure that any repairs to your unit are only carried out by qualifi ed personnel. Opening the unit and attempting to repair it yourself results in forfeiture of all warranty claims !

Improper work on the unit can endanger the electrical safety of the unit.

The manufacturer shall accept no liability for accidents caused by the user opening the unit!

Connections

Incorrect wiring of the connections can lead to operating faults or defects on the unit!

Long periods of absence / storms

ATTENTION! Always turn off the unit at the power switch if you will be absent for a long time or there is a storm. This also applies to the other equipment connected to the unit. Wiring harness isolation is also recommended. Note any timer programmes (receiver) and turn the unit on again promptly before the recording time.

Installation location

Every piece of electronic equipment generates heat. However, the heating of this unit lies within the permissible range. Sensitive furniture surfaces and veneers may become discoloured by the effects of heat over time. The feet of the unit can also cause colour changes to treated furniture surfaces. If necessary, place the unit on a suitable stable and fl at base.

Ventilation

The heat occuring in this unit is adequately dissipated. Never install the unit in a cupboard or on shelves with inadequate ventilation. Never cover the cooling slots on the unit!

No not place any objects on top of the unit and maintain at least 10 cm of free space above the unit so that the resulting heat can be dissipated properly

Moisture, sunlight, heat

The unit should be protected from moisture, dripping water and spray. Do not place the unit close to the heating or

expose it to direct sunlight, and do not operate it in damp locations.

7

Image 7
Contents UFD Page Foreword Contents Connection Diagram Password and Child ProtectionSetting System Parameters Installation MenuContents Power supply cable Safety Instructions and Important InformationSAT-IF Connection Connection and SetupConnecting the Unit Receiving System PresetsDolby Connection Inserting Batteries in the Remote ControlTV Connection Audio ConnectionFront View Controls, Displays and ConnectionsFront View Rear View Exit Remote Control Function KeysRemote control instruction sets Important information on the remote controlMenu Concept Operating InstructionsLanguage Selection Key Alphanumeric Assignment of Remote Control Number KeysMenu Structure Important Information Initial SetupGetting Started Initial Setup Time/Timer section Receiver Factory Satellite SettingGeneral On Screen Display OSDHelp Function TV / Radio Channel Message Error MessageChannel Message Radio Video Text Selecting a TV or Radio Programme Programme SelectionReception Status TV / Radio Channel List Selecting TV/Radio Programmes by Number Switching from a TV Programme to a Radio ProgrammeInserting the Smartcard and the CA Module Common InterfaceMenu language Information for Conax, SECA, Viaccess and CryptoWorks Users Timer Settings VPS Signal Setting the Volume Audio SettingsStereo and Two-Channel Sound Playback Your Dolby Digital system Turning Off the Sound MuteEPG Electronic Programme Guide Programme Overview EPGEPG Timer Programming Selecting the Last Programmes Received Managing Channel List/ChannelsFavourite Channel Setting Up a Favourite ChannelRenaming the Favourite Lists Undoing Favourite Selection Selecting a Favourite Channel from a Favourite ListChannel List Mode Favourite, Satellite, Alphabetical Complete Channel List Sorting Channels Deleting Channels Adding Channels Manually Adding/Deleting Satellites Setting Up SatellitesDeleting Satellites Password Factory Setting Password and Child ProtectionSetting the Password and Child Protection Child Protection Locking a Channel Password and Child Protection Child Protection Setting System ParametersSystem Information TV Type Local Time/TimerPicture Format Mode ScreenOscillator Frequency Installation MenuOpening the Installation Menu LNB ConfigurationStandby OperationDiSEqC2 Setting DiSEqC1 SettingAntenna Setup Satellite Search Changing/Searching for/Deleting Transponders DiSEqCTM UFO Setup DiSEqCTM Repeat KHz SignalTone Burst and DiSEqCTM Signal DiSEqCTMRemote Frequency Factory SettingsReset does not delete the pre-programming After resetting, you may need to make all settings againSoftware and Programme List Update During the download, Please wait fl ashes on the screen Connection between Type of connection Connection DiagramOn-Board Network Connection SAT-ZF ConnectionControl Cable Initial Setup Information Important Information on the Turntable before SetupAlignment Satellite Search Manual Correction Alignment Satellite Search Change of Location Reset Reset/ParkPark System Protection Messages Special Messages for TurntableSatellite Lost / Limit Reached Using the  key Turntable Unit Software Download Turntable Unit Software Download Manual Lowering to Park Position Safety InstructionsManual Retraction Service DVB GlossaryEb/No ratio Brief Technical GlossaryDiSEqC components Dolby DigitalVideo bit rate Symbol rateProgramme package Transponder936.2705/B/0505/ZWT Subject to technical changes