Kathrein UFD 170 Remote Frequency, Factory Settings, Reset does not delete the pre-programming

Page 58

Installation Menu

UFO®mini

Remote Frequency

UFO®micro

“Reset” does not delete the pre-programming.

In a “subscriber controlled processing system”, the input frequency of the receiver is a fi xed setting. The “subscriber controlled processing system” transmits the signals at this frequency. The reception parameters for programme selection are communicated to the receiving system by a DiSEqC™ command and set.

The setting that has to be selected depends on the design of the “subscriber controlled processing system”.

If you have set the “UFO®mini” menu option to “On”, use this menu option to make the setting from the transmission frequency.

For the transmission frequency to be set, refer to the installation manual for the “subscriber controlled processing system”.

It is essential that you follow the instructions in the “subscriber controlled processing system ” installation manual.

The setting for this menu option is also designed for operation of the receiver in a processing system.

The return path of the coaxial cable is used for control and communication between the receiver and the Kathrein UFO®micro system. If the receiver is operated in a UFO®micro receiving system, the “UFO®micro” menu option must be set to “On”.

The receiving system then assigns the receiver a special address upon installation, so that it will recognise the control commands sent by the receiver to the receiving system for signal selection.

In this operating mode, a remote frequency need not be set, as it is specifi ed by the UFO®micro system with the addressing.

If the receiver is being used in a UFO®micro receiving system for the fi rst time, the address previously assigned must be deleted. This is done in the “UFO®micro” menu option by selecting “Reset” using the

 and keys. The receiver is then assigned the original factory setting. It then needs to be set to “On” again. The receiver receives its new address from the new system.

Default setting: “Off”.

Factory Settings

This item allows all parameters to be reset to the factory settings using

the key. The factory settings do not necessarily correspond to the settings required for your specifi c system.

After resetting, you may need to make all settings again.

58

Page 57 Page 59
Image 58
Page 57 Page 59
Contents UFD Page Foreword Contents Installation Menu Password and Child ProtectionSetting System Parameters Connection DiagramContents Safety Instructions and Important Information Power supply cableReceiving System Presets Connection and SetupConnecting the Unit SAT-IF ConnectionAudio Connection Inserting Batteries in the Remote ControlTV Connection Dolby ConnectionFront View Controls, Displays and ConnectionsFront View Rear View Remote Control Function Keys ExitImportant information on the remote control Remote control instruction setsMenu Concept Operating InstructionsLanguage Selection Alphanumeric Assignment of Remote Control Number Keys KeyMenu Structure Important Information Initial SetupGetting Started Initial Setup Receiver Factory Satellite Setting Time/Timer sectionGeneral On Screen Display OSDHelp Function TV / Radio Channel Message Error MessageChannel Message Radio Video Text Selecting a TV or Radio Programme Programme SelectionReception Status TV / Radio Channel List Switching from a TV Programme to a Radio Programme Selecting TV/Radio Programmes by NumberCommon Interface Inserting the Smartcard and the CA ModuleMenu language Information for Conax, SECA, Viaccess and CryptoWorks Users Timer Settings VPS Signal Setting the Volume Audio SettingsStereo and Two-Channel Sound Playback Turning Off the Sound Mute Your Dolby Digital systemProgramme Overview EPG EPG Electronic Programme GuideEPG Timer Programming Managing Channel List/Channels Selecting the Last Programmes ReceivedSetting Up a Favourite Channel Favourite ChannelRenaming the Favourite Lists Selecting a Favourite Channel from a Favourite List Undoing Favourite SelectionChannel List Mode Favourite, Satellite, Alphabetical Complete Channel List Sorting Channels Deleting Channels Adding Channels Manually Setting Up Satellites Adding/Deleting SatellitesDeleting Satellites Password Factory Setting Password and Child ProtectionSetting the Password and Child Protection Child Protection Locking a Channel Password and Child Protection Child Protection Setting System ParametersSystem Information TV Type Local Time/TimerPicture Format Screen ModeLNB Configuration Installation MenuOpening the Installation Menu Oscillator FrequencyOperation StandbyDiSEqC1 Setting DiSEqC2 SettingAntenna Setup Satellite Search Changing/Searching for/Deleting Transponders DiSEqCTM UFO Setup DiSEqCTM KHz SignalTone Burst and DiSEqCTM Signal DiSEqCTM RepeatAfter resetting, you may need to make all settings again Factory SettingsReset does not delete the pre-programming Remote FrequencySoftware and Programme List Update During the download, Please wait fl ashes on the screen Connection Diagram Connection between Type of connectionOn-Board Network Connection SAT-ZF ConnectionControl Cable Important Information on the Turntable before Setup Initial Setup InformationAlignment Satellite Search Manual Correction Alignment Satellite Search Change of Location Reset/Park ResetPark System Protection Messages Special Messages for TurntableSatellite Lost / Limit Reached Using the  key Turntable Unit Software Download Turntable Unit Software Download Safety Instructions Manual Lowering to Park PositionManual Retraction Service Glossary DVBDolby Digital Brief Technical GlossaryDiSEqC components Eb/No ratioTransponder Symbol rateProgramme package Video bit rate936.2705/B/0505/ZWT Subject to technical changes
Top Page Image Contents