SET UP for USE, Channel SET UP for First Time

ADD / DELETE

SET UP FOR USE

You can program the tuner to scan all the channels you receive in your area.

NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3). Then select the channel to be viewed on the Cable Box or Satellite Box.

CHANNEL SET UP FOR THE

FIRST TIME

1Plug in the TV/VCR power cord

Attach the smaller end of the sup- plied AC cord to the AC 120V connector on the back of the

DELETING (OR ADDING)

CHANNEL

The channels you no longer receive or seldom watch can be deleted from the memory. (Of course, you can add the deleted channel into the memory again.)

TV/VCR. Then, plug the other end into a standard AC outlet.

NOTE:

•You must disconnect the car battery cord from the TV/VCR before you use AC power.

•If some digits appear in the corner of the screen, press the POWER button without unplugging the power cord.

1Select “CHANNEL SET UP”

Press the MENU button on the remote control.

Press the PLAY/K or STOP/L but- ton to point to “CHANNEL SET UP”.

Then, press the F.FWD/B button.

– M E N U –

TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK

BCHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN

TIME SEARCH

2Turn on the TV/VCR

Press the POWER button to turn on the TV/VCR.

3Select “ENGLISH” or “FRANÇ AIS”

Select “ENGLISH” or	– SET UP –
“FRANÇAIS”=French using the	B LANGUAGE
F.FWD/B or REW/s button. “[ ]”	[ENGLISH] FRANÇ AIS
F.FWD/B or REW/s button. “[ ]”
indicate the selected language.	AUTO PRESET

4 Begin auto preset

	Press the PLAY/K or STOP/L but-	– SET UP –
	Press the PLAY/K or STOP/L but-
	ton to point to “AUTO PRESET”.	[ENGLISH] FRANÇ AIS
		LANGUAGE
	Then press the F.FWD/B button.	B AUTO PRESET
	The tuner scans and memorizes all	B AUTO PRESET
	The tuner scans and memorizes all
	active channels in your area.

NOTES:

•The TV/VCR distinguishes between standard TV channels and cable channels.

•If you want to play or record a video tape BEFORE presetting the tuner, you must press the MENU button on the remote control. To preset the tuner again, see “CHANNEL SET UP AGAIN” on page 13.

•The TV/VCR may recognize TV channels to be CATV channels by the receiving conditions. In this case, try auto preset again in the fine receiving conditions.

5After scanning

The tuner stops on the lowest memorized channel. If you want to recall the selected channels, you can select the desired channel directly with the remote control number buttons or CHANNEL K or L button.

2 Select “ADD/DELETE CH”	– CHANNEL SET UP –
Press the PLAY/K or STOP/L but-	B ADD / DELETE CH (TV)
ton to point to “ADD/DELETE	AUTO PRESET
ton to point to “ADD/DELETE
CH”.
Press the F.FWD/B button.

3Enter the desired channel number

Press the PLAY/K or STOP/L but- ton until your desired channel num- ber appears. (You can also use the

number buttons or the CHANNEL K/L button to enter it.) (Example: CH8)

4Delete (or add) it from (into) memory

Press the F.FWD/B or REW/s button. The channel number changes to light red. The channel is deleted from memory.

•To delete another channel, repeat steps [3] and [4].

Added channel: Light blue.

Deleted channel: Light red.

•If you press the F.FWD/B or REW/s button again, the channel is memorized again.

5Exit the channel setup mode

Press the MENU button on the remote control to returns to TV mode.

NOTE: To confirm that channel(s) has been deleted or added, press the CHANNEL K or L button.

- 12 -

0B19