Integra DPS-10.5 instruction manual Learning the Commands of Other Remote Controllers, Mode

Controlling Other Components—Continued

On	On	Standby		TV
				I	Input
	1		2	3	+
					TV CH
	4		5	6	-
	7		8	9
					TV VOL
	+10		0	Clear
Search		Memory		Dimmer	Amp Input
	S		M	D	Input
			Amp Input
	DVD		V1	V2	V3
Mode			Mode
	DVD		Amp	VCR	TV
Zoom On					Picture Control
Audio			enu	M
		opM		enu
Sel		T
	+
	CH
	Zoom		Enter		VOL
	L Mode
	-
		R	eturn	p
				Setu
Display					Muting
Last Memory			Step/Slow		Random
Rec	LM				RD
	Audio	Subtitle		Angle	Resolution
	Audio	Subtitle		Angle	Rsltn
	Repeat		A-B		Aspect
	Repeat		A-B		Aspect
Video Input		Video Off		Learning
	V In		V Off	L1	L 2
Open/Close
				L 3	L 4
			RC-562DV

Learning the Commands of Other Remote Controllers

The DPS-10.5’s remote controller can learn individual commands from other component’s remote controllers and then be used to control those components. Com- mands can be learnt by the dedicated leaning buttons— [L1], [L2], [L3], and [L4]—or any button. Each button can learn up to four commands, one for each remote con- troller mode: DVD, Amp, VCR, and TV.

If you’ve entered a control code for a component (page 82) and certain buttons don’t work as expected, you can also use this function to program those buttons individually.

1 Point the remote controllers at each other, about 2 to 6 inches (5–15 cm) apart.

							EM
							ULOV		G
							SETOT		NIT UM
									LEVEL
							T EN
							LES	HC
		T	ESE
D
	C		RERNP	DVD					EPAT
		ONOH	UT	PU
E		ROP		O
RUDSOM			TCELREENU	RG	2-	EDIV	C
2–6" (5–15 cm)			PEELSR E		D VD		ISD
			ST UT		OE	DC
		REMMID		PINEPAT	IDV 1-O
				WOP

RC-563DV

2 While holding down the [DVD], [Amp], [VCR], or [TV] Mode button, press the [On] button, and then release both buttons.

The Mode button and Tx/Learn indicator light up.

3 On the DPS-10.5’s remote controller, press the button that you want to learn the new command.

The Tx/Learn indicator goes off while the button is being pressed, and comes back on again when it’s released.

Use the dedicated leaning buttons—[L1], [L2], [L3], and [L4]—or another button.

4 On the other remote controller, press and hold the button whose command you want to learn until the Tx/Learn indicator flashes.

If the command is learnt successfully, the Tx/ Learn indicator flashes slowly twice, and then the Mode button and Tx/Learn indicator remain lit. If the Tx/Learn indicator flashes quickly three times, the command has not been learnt, in which case you should try again from step 3.

If the Tx/Learn indicator flashes quickly six times, the remote controller’s memory is full and no more commands can be learnt.

5 To learn more new commands, repeat steps 3 and 4.

When you’ve finished, press the Mode button that you pressed in step 2.

To use the learnt command, select the relevant mode, and then press the button.

Notes:

•The following buttons cannot learn new commands: [LIGHT] and the [DVD], [Amp], [VCR], and [TV] Mode buttons.

•Learning mode is cancelled automatically if you don’t press any buttons for 30 seconds.

•The DPS-10.5’s remote controller comes prepro- grammed with the commands necessary for control- ling Integra DVD players (DVD mode) and AV receivers (Amp mode). However, you can reprogram individual buttons if necessary. The original com- mands can be restored by resetting the remote controller.

•To program a button that has already learnt a com- mand, repeat this procedure. The previously learnt command will be overwritten.

•Like most remote controllers, the DPS-10.5’s remote controller uses infrared. Commands from remote con- trollers that don’t use infrared cannot be learnt.

•When the remote controller’s batteries expire, all learnt commands may be lost and will have to be learnt all over again, so keep your other remote controllers in a safe place.

87