Dukane 8063, 8755C user manual Lamp

Page 10

Lamp

WARNING

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

About disposal of a lamp • This product contains a mercury lamp; do not put in trash. Dispose of in accord with environmental laws.

For lamp recycling, go to www.lamprecycle.org. (in USA)

For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada).

For more information, call your dealer.

• If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

• If the lamp should break (it will make a loud bang when it does), Disconnect the ventilate the room well, and make sure not to breathe the gas that comes

plug from the

out of the projector vents, or get it in your eyes or mouth.

power outlet

• Before replacing the lamp, make sure the power switch is off and the

 

power cable is not plugged in, then wait at least 45 minutes for the lamp

 

to cool sufficiently. Handling the lamp while hot can cause burns, as well

 

as damaging the lamp.

 

 

 

• Do not open the lamp cover while the projector is suspended from above.

 

This is dangerous, since if the lamp’s bulb has broken, the shards will

 

fall out when the cover is opened. In addition, working in high places is

 

dangerous, so ask your local dealer to have the lamp replaced even if the

 

bulb is not broken.

 

• Do not use the projector with the lamp cover removed. At the lamp

 

replacing, make sure that the screws are screwed in firmly. Loose screws

 

could result in damage or injury.

 

 

 

• Use the lamp of the specified type only.

 

• If the lamp breaks soon after the first time it is used, it is possible that

 

there are electrical problems elsewhere besides the lamp. If this happens,

 

contact your local dealer or a service representative.

 

• Handle with care: jolting or scratching could cause the lamp bulb to burst

 

during use.

 

• If the indicators or a message prompts you to replace the lamp (see the

 

section “Related Messages” and “Regarding the indicator Lamps”),

 

replace the lamp as soon as possible. Using the lamp for long periods of

 

time, or past the replacement date, could cause it to burst. Do not use old

 

(used) lamps; this is a cause of breakage.

8

Image 10
Contents LCD Projector Model 8063/8755C Operators Guide Contents About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page Thank you for purchasing this projector About this manualTrademark acknowledgment Contents About contents of package Projector featuresPreparations Projector CB/PB CR/PRRemote control Control buttonsSetting up At 43 screen ArrangementAt 169 screen Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityConnecting to a speaker with amplifier output Connecting to a monitor outputExamples of connection with a computer CR/PR Examples of connection with a VCR/DVD playerCB/PB Connecting power supply Remote control Putting batteriesUsing the remote control Turning off the power Power on/offTurning on the power PowerOperating Adjusting the volumeSelecting an input signal Temporarily muting the sound At a RGB signal Normal  43  Searching an input signalAdjusting the zoom and focus  At a video signal /no signal 43  169  Small At a RGB signal Using the automatic adjustment featureAdjusting the position  At a video signalFreezing the screen Using the magnify featureTemporarily blanking the screen Operating the computer screen Available function Remote control operationUSB mouse and keyboard control Multifunctional settings Using the menu functionEasy Menu Easy Menu Picture Menu GammaColor Temp Picture MenuHigh  Middle  LOW  Custom SecamLOAD1  LOAD2  LOAD3  LOAD4 TV  Film  Turn OFFProgressive SAVE4 SAVE3  SAVE2  SAVE1Over Scan PhaseImage Menu PositionImage Menu Auto AdjustAt a video signal SizeAuto  Ntsc  PAL  Secam Input MenuComponent  Scart RGB Video FormatInput Menu InformationNormal  Whisper Setup MenuVolume Normal  Hinvert  Vinvert  H&VINVERTOSD Bright Screen MenuMenu Position BlankMy Screen Screen MenuStart UP My Screen LockMessage No Input is Detected Sync is OUT of RangeSearch Reset  CancelOption Menu Auto OFFOption Menu Service GhostFactory Reset FAN SpeedMaintenance LampCase of replacement by yourself LampApply a vacuum cleaner to the air filter and filter cover Air filterEnglish Internal portion temperature is rising There is no input signalRelated messages Related messages Message DescriptionRegarding the indicator lamps Cooling fan is not operating Regarding the indicator lampsIt is time to clean the air filter There is a possibility that the interior portionThese has not been properly fixed Electrical power cord is not pluggedPower switch is not set to the on position Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects RGB output SpecificationRGB input Video input Communication portSpecifications Page Vesa Text Example of computer signalVesa Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTComponent Video G Y, H CB/PB, I CR/PR RTS CTSCommunications setting Connecting the cableRS-232C Communication Using the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Over Scan Frame Lock Menu Position H Lamp Time Page Audio Visual Products