Dukane 8063 Related messages, There is no input signal, Internal portion temperature is rising

Page 54

Troubleshooting

Troubleshooting

Related messages

When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below. If the same message is displayed after the treatment, or if a message other than the following appears, please contact your dealer or service company.

Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.

Message

Description

CHANGE THE LAMP

The time the lamp timer has counted is approaching

2000 hours.

 

AFTER REPLACING LAMP,

Preparation of a new lamp, and an early lamp change is

recommended. After you have change the lamp, please be

RESET THE LAMP TIMER.

sure to reset the lamp timer (36).

 

CHANGE THE LAMP

The time the lamp timer has counted is approaching

 

2000 hours, so a lamp change within ** hours is

AFTER REPLACING LAMP,

recommended.

RESET THE LAMP TIMER.

When lamp usage reaches 2000 hours, the power will

THE POWER WILL TURN OFF

automatically be turned off. Please change the lamp by

referring to the section “Lamp”. After you have changed the

AFTER ** hr.

lamp, please be sure to reset the lamp timer (36).

CHANGE THE LAMP

As the time the lamp timer has counted has reached

AFTER REPLACING LAMP,

2000 hours, the power will soon be automatically

turned off.

RESET THE LAMP TIMER.

Please immediately turn the power off, and change the lamp

 

THE POWER WILL TURN OFF

by referring to the section “Lamp”. After changing the lamp,

AFTER 0 hr.

please be sure to reset the lamp timer (36).

NO INPUT IS DETECTED

There is no input signal.

Please confirm the signal input connection, and the status

ON ***

of the signal source.

 

SYNC IS OUT OF RANGE

The horizontal or vertical wavelength of the inputted

signal is outside of the response parameters of this unit.

ON *** fH *****kHz fV *****Hz

 

Please confirm the specs for this unit or the signal source specs.

 

The internal portion temperature is rising.

 

Please turn the power OFF, and allow the unit to cool down at least 20 minutes.

 

After having confirmed the following items, please turn the power ON again.

CHECK THE AIR FLOW

• Is there blockage of the air passage aperture?

• Is the air filter dirty?

 

 

• Does the peripheral temperature exceed 35°C?

 

• If the same indication is displayed after the treatment, please set the

 

HIGH at the FAN SPEED of the item SERVICE of the OPTION menu.

42

Image 54
Contents LCD Projector Model 8063/8755C Operators Guide Contents About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents Projector features About contents of packagePreparations Projector CB/PB CR/PRRemote control Control buttonsSetting up Arrangement At 43 screenAt 169 screen Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityConnecting to a monitor output Connecting to a speaker with amplifier outputExamples of connection with a computer Examples of connection with a VCR/DVD player CR/PRCB/PB Connecting power supply Remote control Putting batteriesUsing the remote control Turning off the power Power on/offTurning on the power PowerOperating Adjusting the volumeSelecting an input signal Temporarily muting the sound At a RGB signal Normal  43  Searching an input signalAdjusting the zoom and focus  At a video signal /no signal 43  169  Small At a RGB signal Using the automatic adjustment featureAdjusting the position  At a video signalUsing the magnify feature Freezing the screenTemporarily blanking the screen Available function Remote control operation Operating the computer screenUSB mouse and keyboard control Multifunctional settings Using the menu functionEasy Menu Easy Menu Picture Menu GammaColor Temp Picture MenuHigh  Middle  LOW  Custom SecamLOAD1  LOAD2  LOAD3  LOAD4 TV  Film  Turn OFFProgressive SAVE4 SAVE3  SAVE2  SAVE1Over Scan PhaseImage Menu PositionImage Menu Auto AdjustAt a video signal SizeAuto  Ntsc  PAL  Secam Input MenuComponent  Scart RGB Video FormatInput Menu InformationNormal  Whisper Setup MenuVolume Normal  Hinvert  Vinvert  H&VINVERTOSD Bright Screen MenuMenu Position BlankMy Screen Screen MenuStart UP My Screen LockMessage No Input is Detected Sync is OUT of RangeSearch Reset  CancelOption Menu Auto OFFOption Menu Service GhostFactory Reset FAN SpeedMaintenance LampCase of replacement by yourself LampApply a vacuum cleaner to the air filter and filter cover Air filterEnglish There is no input signal Internal portion temperature is risingRelated messages Related messages Message DescriptionRegarding the indicator lamps Cooling fan is not operating Regarding the indicator lampsIt is time to clean the air filter There is a possibility that the interior portionThese has not been properly fixed Electrical power cord is not pluggedPower switch is not set to the on position Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects RGB output SpecificationRGB input Video input Communication portSpecifications Page Example of computer signal Vesa TextVesa Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTComponent Video G Y, H CB/PB, I CR/PR RTS CTSConnecting the cable Communications settingRS-232C Communication Using the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Over Scan Frame Lock Menu Position H Lamp Time Page Audio Visual Products