Dukane 8755C, 8063 user manual Regulatory Notices

Page 11

Regulatory Notices

FCC Statement Warning

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

INSTRUCTIONS TO USERS: This equipment complies with the requirements of FCC (Federal Communication Commission) equipment provided that the following conditions are met. Some cables have to be used with the core set. Use the accessory cable or a designated-type cable for the connection. For cables that have a core only at one end, connect the core to the projector.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

For the Customers in CANADA

NOTICE: This Class B digital apparatus complies with Canadian ICES-003.

Warranty And After-Service

Unless seen any abnormal operations (mentioned with the first paragraph of WARNING in this manual), when a problem occurs with the equipment, first refer to the “Troubleshooting” section of the “User’s manual – Operating Guide”, and run through the suggested checks.

If this does not resolve the problem contact your dealer or service company. They will tell you what warranty condition is applied.

9

Image 11
Contents LCD Projector Model 8063/8755C Operators Guide Contents About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page Trademark acknowledgment About this manualThank you for purchasing this projector Contents Preparations Projector featuresAbout contents of package CB/PB CR/PR ProjectorControl buttons Remote controlSetting up At 169 screen ArrangementAt 43 screen Adjusting the projectors elevator About the filter cover for bottom-up use About Plug-and-Play capability Connecting your devicesExamples of connection with a computer Connecting to a monitor outputConnecting to a speaker with amplifier output CB/PB Examples of connection with a VCR/DVD playerCR/PR Connecting power supply Putting batteries Remote controlUsing the remote control Power Power on/offTurning on the power Turning off the powerTemporarily muting the sound Adjusting the volumeSelecting an input signal Operating At a video signal /no signal 43  169  Small Searching an input signalAdjusting the zoom and focus  At a RGB signal Normal  43  At a video signal Using the automatic adjustment featureAdjusting the position  At a RGB signalTemporarily blanking the screen Using the magnify featureFreezing the screen USB mouse and keyboard control Available function Remote control operationOperating the computer screen Using the menu function Multifunctional settingsEasy Menu Easy Menu Gamma Picture MenuSecam Picture MenuHigh  Middle  LOW  Custom Color TempSAVE4 SAVE3  SAVE2  SAVE1 TV  Film  Turn OFFProgressive LOAD1  LOAD2  LOAD3  LOAD4Position PhaseImage Menu Over ScanSize Auto AdjustAt a video signal Image MenuVideo Format Input MenuComponent  Scart RGB Auto  Ntsc  PAL  SecamInformation Input MenuNormal  Hinvert  Vinvert  H&VINVERT Setup MenuVolume Normal  WhisperBlank Screen MenuMenu Position OSD BrightMy Screen Lock Screen MenuStart UP My ScreenNo Input is Detected Sync is OUT of Range MessageAuto OFF Reset  CancelOption Menu SearchFAN Speed Service GhostFactory Reset Option MenuLamp MaintenanceLamp Case of replacement by yourselfAir filter Apply a vacuum cleaner to the air filter and filter coverEnglish Related messages There is no input signalInternal portion temperature is rising Message Description Related messagesRegarding the indicator lamps There is a possibility that the interior portion Regarding the indicator lampsIt is time to clean the air filter Cooling fan is not operatingPhenomenon Cases not involving a machine defect Reference Electrical power cord is not pluggedPower switch is not set to the on position These has not been properly fixedPhenomena that may easily be mistaken for machine defects Communication port SpecificationRGB input Video input RGB outputSpecifications Page Vesa Example of computer signalVesa Text Initial set signals RGB in 1, B RGB in 2, C RGB OUT Connection to the portsComponent Video G Y, H CB/PB, I CR/PR CTS RTSRS-232C Communication Connecting the cableCommunications setting Increasing the projector setting value Increment command Requesting projector status Get commandChanging the projector settings Set command Using the projector default settings Reset CommandCRC Be EF FB FA Color Temp Gain G Over Scan Frame Lock Menu Position H Lamp Time Page Audio Visual Products