Dukane 8755C, 8063 user manual Easy Menu

Page 35

Multifunctional settings

EASY Menu

With the EASY MENU, items shown in the table below can be performed.

Select an item using the cursor buttons ▲/▼ on the projector or remote control. Then perform it referring to the following table.

EASY MENU

ASPECT

4:3

KEYSTONE

+0

 

 

MODE

NORMAL

BRIGHT

+0

 

 

CONTRAST

+0

COLOR

 

+0

 

 

TINT

+0

SHRPNESS

 

+3

WHISPER

 

NORMAL

MIRROR

NORMAL

RESET

EXECUTE

FILTER TIME

0

LANGUAGE

ENGLISH

Go To Advance Menu...

ENGLISH

Item

Description

ASPECT

Using the buttons ◄/► switches the mode for aspect ratio.

See the item ASPECT of section IMAGE menu (28).

 

KEYSTONE

Using the buttons ◄/► corrects the keystone distortion.

See the item KEYSTONE of section SETUP menu (32).

 

 

Using the buttons ◄/► switches the mode of picture type.The

 

modes of picture type are combinations of a mode of GAMMA and

 

a mode of COLOR TEMP. Choose a suitable mode according to the

 

projected source.

 

NORMAL CINEMA DYNAMIC

MODE

NORMAL: (COLOR TEMP = MIDDLE) + (GAMMA = #1 DEFAULT)

 

CINEMA: (COLOR TEMP = LOW) + (GAMMA = #2 DEFAULT)

 

DYNAMIC: (COLOR TEMP = HIGH) + (GAMMA = #3 DEFAULT)

 

• When the combination of GAMMA and COLOR TEMP differs

 

from pre-assigned modes above, the display on the menu for the

 

MODE is “CUSTOM”. Please refer to the items GAMMA (25) and

 

COLOR TEMP (26) of PICTURE menu.

BRIGHT

Using the buttons ◄/► adjusts the brightness.

See the item BRIGHT of section PICTURE menu (25).

 

CONTRAST

Using the buttons ◄/► adjusts the contrast.

See the item CONTRAST of section PICTURE menu (25).

 

COLOR

Using the buttons ◄/► adjusts the strength of whole color.

See the item COLOR of section PICTURE menu (26).

 

TINT

Using the buttons ◄/► adjusts the tint.

See the item TINT of section PICTURE menu (26).

 

23

Image 35
Contents LCD Projector Model 8063/8755C Operators Guide Contents About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page Trademark acknowledgment About this manualThank you for purchasing this projector Contents Preparations Projector featuresAbout contents of package CB/PB CR/PR ProjectorControl buttons Remote controlSetting up At 169 screen ArrangementAt 43 screen Adjusting the projectors elevator About the filter cover for bottom-up use About Plug-and-Play capability Connecting your devicesExamples of connection with a computer Connecting to a monitor outputConnecting to a speaker with amplifier output CB/PB Examples of connection with a VCR/DVD playerCR/PR Connecting power supply Putting batteries Remote controlUsing the remote control Power Power on/offTurning on the power Turning off the powerTemporarily muting the sound Adjusting the volumeSelecting an input signal Operating At a video signal /no signal 43  169  Small Searching an input signalAdjusting the zoom and focus  At a RGB signal Normal  43  At a video signal Using the automatic adjustment featureAdjusting the position  At a RGB signalTemporarily blanking the screen Using the magnify featureFreezing the screen USB mouse and keyboard control Available function Remote control operationOperating the computer screen Using the menu function Multifunctional settingsEasy Menu Easy Menu Gamma Picture MenuSecam Picture MenuHigh  Middle  LOW  Custom Color TempSAVE4 SAVE3  SAVE2  SAVE1 TV  Film  Turn OFFProgressive LOAD1  LOAD2  LOAD3  LOAD4Position PhaseImage Menu Over ScanSize Auto AdjustAt a video signal Image MenuVideo Format Input MenuComponent  Scart RGB Auto  Ntsc  PAL  SecamInformation Input MenuNormal  Hinvert  Vinvert  H&VINVERT Setup MenuVolume Normal  WhisperBlank Screen MenuMenu Position OSD BrightMy Screen Lock Screen MenuStart UP My ScreenNo Input is Detected Sync is OUT of Range MessageAuto OFF Reset  CancelOption Menu SearchFAN Speed Service GhostFactory Reset Option MenuLamp MaintenanceLamp Case of replacement by yourselfAir filter Apply a vacuum cleaner to the air filter and filter coverEnglish Related messages There is no input signalInternal portion temperature is rising Message Description Related messagesRegarding the indicator lamps There is a possibility that the interior portion Regarding the indicator lampsIt is time to clean the air filter Cooling fan is not operatingPhenomenon Cases not involving a machine defect Reference Electrical power cord is not pluggedPower switch is not set to the on position These has not been properly fixedPhenomena that may easily be mistaken for machine defects Communication port SpecificationRGB input Video input RGB outputSpecifications Page Vesa Example of computer signalVesa Text Initial set signals RGB in 1, B RGB in 2, C RGB OUT Connection to the portsComponent Video G Y, H CB/PB, I CR/PR CTS RTSRS-232C Communication Connecting the cableCommunications setting Increasing the projector setting value Increment command Requesting projector status Get commandChanging the projector settings Set command Using the projector default settings Reset CommandCRC Be EF FB FA Color Temp Gain G Over Scan Frame Lock Menu Position H Lamp Time Page Audio Visual Products