Dukane 8063, 8755C user manual Projector, Cb/Pb Cr/Pr

Page 16

Part names

Part names

Projector

Remote sensor (15)

Zoom knob (18)

Speaker (6)

Focus ring (18)

Vent (6)

Lens cover (16)

(Slide door)

Lens (16)

Lamp cover

(Lamp unit is inside.) (38)

Control buttons (See the following page.) (5)

Front-Right side

Bottom side

Elevator button (8)

Elevator foot (8)

Filter cover (40)

(Air filter and intake vent are inside.)

Power switch (16)

AC inlet (13)

Elevator button (8)

Ports

(See below.)

AUDIO OUT port (11) AUDIO IN1 port (11) S-VIDEO port (12)

COMPONENT VIDEO ports (12)

Y

CB/PB

CR/PR

VIDEO port (12) AUDIO IN2 port (11) USB port (11)

Y

CB/PB

VIDEO

CR/PR S-VIDEO

COMPONENT VIDEO

 

Elevator foot (8)

 

Vent (6)

Rear-Left side

Restart switch (*) (46)

 

 

RGB IN1 port (11)

 

RGB IN2 port (11)

AUDIO IN1

RGB OUT port (11)

AUDIO OUTRGB IN1RGB IN2RGB OUT

AUDIO IN2

CONTROL port (11)

USB

Kensington lock slot

CONTROL

Ports

 

NOTE (*) About Restart switch: This Projector is controlled by an internal microprocessor. Under certain exceptional circumstances, the projector may not operate correctly and the microprocessor will need to be reset. In such a case, please push the Restart switch by using a cocktail stick or similar and before turning on again, make the projector cool down at least 10 minutes without operating. Only push the Restart switch in these exceptional instances.

4

Image 16
Contents LCD Projector Model 8063/8755C Operators Guide Contents About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page Thank you for purchasing this projector About this manualTrademark acknowledgment Contents About contents of package Projector featuresPreparations Projector CB/PB CR/PRRemote control Control buttonsSetting up At 43 screen ArrangementAt 169 screen Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityConnecting to a speaker with amplifier output Connecting to a monitor outputExamples of connection with a computer CR/PR Examples of connection with a VCR/DVD playerCB/PB Connecting power supply Remote control Putting batteriesUsing the remote control Power on/off Turning on the powerTurning off the power PowerAdjusting the volume Selecting an input signalOperating Temporarily muting the soundSearching an input signal Adjusting the zoom and focus At a RGB signal Normal  43   At a video signal /no signal 43  169  SmallUsing the automatic adjustment feature Adjusting the position At a RGB signal  At a video signalFreezing the screen Using the magnify featureTemporarily blanking the screen Operating the computer screen Available function Remote control operationUSB mouse and keyboard control Multifunctional settings Using the menu functionEasy Menu Easy Menu Picture Menu GammaPicture Menu High  Middle  LOW  CustomColor Temp SecamTV  Film  Turn OFF ProgressiveLOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1Phase Image MenuOver Scan PositionAuto Adjust At a video signalImage Menu SizeInput Menu Component  Scart RGBAuto  Ntsc  PAL  Secam Video FormatInput Menu InformationSetup Menu VolumeNormal  Whisper Normal  Hinvert  Vinvert  H&VINVERTScreen Menu Menu PositionOSD Bright BlankScreen Menu Start UPMy Screen My Screen LockMessage No Input is Detected Sync is OUT of RangeReset  Cancel Option MenuSearch Auto OFFService Ghost Factory ResetOption Menu FAN SpeedMaintenance LampCase of replacement by yourself LampApply a vacuum cleaner to the air filter and filter cover Air filterEnglish Internal portion temperature is rising There is no input signalRelated messages Related messages Message DescriptionRegarding the indicator lamps Regarding the indicator lamps It is time to clean the air filterCooling fan is not operating There is a possibility that the interior portionElectrical power cord is not plugged Power switch is not set to the on positionThese has not been properly fixed Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects Specification RGB input Video inputRGB output Communication portSpecifications Page Vesa Text Example of computer signalVesa Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTComponent Video G Y, H CB/PB, I CR/PR RTS CTSCommunications setting Connecting the cableRS-232C Communication Requesting projector status Get command Changing the projector settings Set commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Over Scan Frame Lock Menu Position H Lamp Time Page Audio Visual Products