Dukane 8063, 8755C user manual Option Menu, Search, Auto OFF, Lamp Time, Reset  Cancel

Page 48

Multifunctional settings

OPTION Menu

With the OPTION menu, items shown in the table below can be performed.

Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress, except for the items LAMP TIME and FILTER TIME. Then perform it referring to the following table.

MENU [RGB]

 

:SELECT

PICTURE

SEARCH

TURN ON

IMAGE

AUTO OFF

0

INPUT

LAMP TIME

0

SETUP

FILTER TIME

0

SCREEN

SERVICE

 

OPTION

 

 

EASY MENU

 

 

Item

Description

 

Using the buttons ▲/▼ turns on/off the message function.

 

TURN ON TURN OFF

 

 

When the TURN ON is selected, detecting no signal automatically

SEARCH

cycles through input ports in order of following. Then when an input

is found, the projector will stop searching and display the image.

 

If no signal is found, the projector will return to the state before the

 

operation.

 

 

RGB IN1 RGB IN2 COMPONENT VIDEO S-VIDEO VIDEO

 

 

 

Using the buttons ▲/▼ adjusts the time to count down to

 

automatically turn the projector off.

 

 

Long (max. 99 minutes) Short (min. 0 minute = DISABLE)

 

AUTO OFF

AUTO OFF

 

ENABLE

DISABLE

AUTO OFF

1

0

When the time is set to 0, the projector is not turned off

 

 

automatically.

 

 

When the time is set to 1 to 99, and when the passed time with

 

a no-signal or an unsuitable signal reaches at the set time, the

 

projector lamp will go off and the power indicator begins blinking.

 

Please refer to the section “Turning off the power” (16).

 

The lamp time is the time counted after the last resetting. It is

 

shown in the OPTION menu as the use time of the lamp.

 

Pressing the RESET button on the remote control for about 3

 

seconds displays a dialog. To reset the lamp time, select the

LAMP TIME

RESET using the button ▲.

 

RESET CANCEL

 

 

 

 

• Please reset the lamp time only when you have replaced the lamp,

 

for correct messages about the lamp.

 

 

• About the lamp replacement, please see the section "Lamp" (

 

38, 39).

 

36

Image 48
Contents LCD Projector Model 8063/8755C Operators Guide Contents About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents Projector features About contents of packagePreparations Projector CB/PB CR/PRRemote control Control buttonsSetting up Arrangement At 43 screenAt 169 screen Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityConnecting to a monitor output Connecting to a speaker with amplifier outputExamples of connection with a computer Examples of connection with a VCR/DVD player CR/PRCB/PB Connecting power supply Remote control Putting batteriesUsing the remote control Power on/off Turning on the powerTurning off the power PowerAdjusting the volume Selecting an input signalOperating Temporarily muting the soundSearching an input signal Adjusting the zoom and focus At a RGB signal Normal  43   At a video signal /no signal 43  169  SmallUsing the automatic adjustment feature Adjusting the position At a RGB signal  At a video signalUsing the magnify feature Freezing the screenTemporarily blanking the screen Available function Remote control operation Operating the computer screenUSB mouse and keyboard control Multifunctional settings Using the menu functionEasy Menu Easy Menu Picture Menu GammaPicture Menu High  Middle  LOW  CustomColor Temp SecamTV  Film  Turn OFF ProgressiveLOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1Phase Image MenuOver Scan PositionAuto Adjust At a video signalImage Menu SizeInput Menu Component  Scart RGBAuto  Ntsc  PAL  Secam Video FormatInput Menu InformationSetup Menu VolumeNormal  Whisper Normal  Hinvert  Vinvert  H&VINVERTScreen Menu Menu PositionOSD Bright BlankScreen Menu Start UPMy Screen My Screen LockMessage No Input is Detected Sync is OUT of RangeReset  Cancel Option MenuSearch Auto OFFService Ghost Factory ResetOption Menu FAN SpeedMaintenance LampCase of replacement by yourself LampApply a vacuum cleaner to the air filter and filter cover Air filterEnglish There is no input signal Internal portion temperature is risingRelated messages Related messages Message DescriptionRegarding the indicator lamps Regarding the indicator lamps It is time to clean the air filterCooling fan is not operating There is a possibility that the interior portionElectrical power cord is not plugged Power switch is not set to the on positionThese has not been properly fixed Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects Specification RGB input Video inputRGB output Communication portSpecifications Page Example of computer signal Vesa TextVesa Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTComponent Video G Y, H CB/PB, I CR/PR RTS CTSConnecting the cable Communications settingRS-232C Communication Requesting projector status Get command Changing the projector settings Set commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Over Scan Frame Lock Menu Position H Lamp Time Page Audio Visual Products