Dukane 8063, 8755C user manual Be careful in handling the light source lamp

Page 6

Safety Precautions (continued)

WARNING

Be careful in handling the light source lamp.

The projector uses a high-pressure mercury glass lamp made of glass. The lamp can break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

Please carefully read the section “Lamp”.

Be careful in handling the power cord and external connection cables. If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat, pressure or tension to the power cord and cables.

If the power cord or cables is damaged (exposed or broken core wires, etc.), contact your dealer.

•Do not place the projector or heavy objects on the power cord and cables. Also, do not place a spread, cover, etc, over them because this could result in the inadvertent placing of heavy objects on the concealed power cord or cables.

•Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand holding the plug or connector.

•Do not place the cord near the heater.

•Avoid bending the power cord sharply.

•Do not attempt to work on the power cord.

Be careful in handling the battery of the remote control.

Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.

•Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.

•Do not allow the battery in a fire or water.

•Avoid fire or high-temperature environment.

•Do not hold the battery with the metallic tweezers.

•Keep the battery in a dark, cool and dry play.

•Do not short circuit the battery.

•Do not recharge, disassemble or solder the battery.

•Do not give the battery a physical impact.

•Use only the battery specified in the other manual of this projector.

•Make sure the plus and minus terminals are correctly aligned when loading the battery.

•If you observe a leakage of the battery, wipe out the flower and then replace the battery. If the flower adheres your body or clothes, rinse well with water.

•Obey the local laws on disposing the battery.

4

Image 6

Contents LCD Projector Model 8063/8755C Operators Guide Contents About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents Projector features About contents of packagePreparations Projector CB/PB CR/PRRemote control Control buttonsSetting up Arrangement At 43 screenAt 169 screen Adjusting the projectors elevator About the ﬁlter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityConnecting to a monitor output Connecting to a speaker with ampliﬁer outputExamples of connection with a computer Examples of connection with a VCR/DVD player CR/PRCB/PB Connecting power supply Remote control Putting batteriesUsing the remote control Turning off the power Power on/offTurning on the power PowerOperating Adjusting the volumeSelecting an input signal Temporarily muting the sound At a RGB signal Normal  43  Searching an input signalAdjusting the zoom and focus  At a video signal /no signal 43  169  Small At a RGB signal Using the automatic adjustment featureAdjusting the position  At a video signalUsing the magnify feature Freezing the screenTemporarily blanking the screen Available function Remote control operation Operating the computer screenUSB mouse and keyboard control Multifunctional settings Using the menu functionEasy Menu Easy Menu Picture Menu GammaColor Temp Picture MenuHigh  Middle  LOW  Custom SecamLOAD1  LOAD2  LOAD3  LOAD4 TV  Film  Turn OFFProgressive SAVE4 SAVE3  SAVE2  SAVE1Over Scan PhaseImage Menu PositionImage Menu Auto AdjustAt a video signal SizeAuto  Ntsc  PAL  Secam Input MenuComponent  Scart RGB Video FormatInput Menu InformationNormal  Whisper Setup MenuVolume Normal  Hinvert  Vinvert  H&VINVERTOSD Bright Screen MenuMenu Position BlankMy Screen Screen MenuStart UP My Screen LockMessage No Input is Detected Sync is OUT of RangeSearch Reset  CancelOption Menu Auto OFFOption Menu Service GhostFactory Reset FAN SpeedMaintenance LampCase of replacement by yourself LampApply a vacuum cleaner to the air ﬁlter and ﬁlter cover Air ﬁlterEnglish There is no input signal Internal portion temperature is risingRelated messages Related messages Message DescriptionRegarding the indicator lamps Cooling fan is not operating Regarding the indicator lampsIt is time to clean the air ﬁlter There is a possibility that the interior portionThese has not been properly ﬁxed Electrical power cord is not pluggedPower switch is not set to the on position Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects RGB output SpeciﬁcationRGB input Video input Communication portSpeciﬁcations Page Example of computer signal Vesa TextVesa Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTComponent Video G Y, H CB/PB, I CR/PR RTS CTSConnecting the cable Communications settingRS-232C Communication Using the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Over Scan Frame Lock Menu Position H Lamp Time Page Audio Visual Products