Dukane 8755C, 8063 user manual About the filter cover for bottom-up use

Page 21

Setting up

About the filter cover for bottom-up use

WARNING ►Do not replace the filter cover during use or immediately after use. While the projector connects with a power supply, or the projector is in a high temperature state, handling could cause an electric shock, a fire, a burn and/or malfunction to the projector.Before handling, make sure the power switch is off and the power cord is not plugged in, then wait at least 45 minutes.

When the projector is installed bottom up, please use the accessory filter cover for bottom-up use. It is higher than usual filter cover, to keep the space for intake ventilation. Please change in the following procedure.

Filter cover’s knob

Filter cover’s knob

 

ENGLISH

Filter cover

To remove

To set

Filter cover for bottom-up use

1. After making sure that the projector is cool adequately, slowly turn the projector so that the lens-side is facing up. Please be careful for a projector

not to fall. While the projector is placed lens-side up, hold the projector.

2. Putting a finger on the filter cover’s knob, slide the filter cover in the direction of the arrow to remove it.

3. Replace the filter cover for bottom-up use and snap it back into place.

4. Slowly turn the projector so that the top is facing up.

9

Image 21
Contents LCD Projector Model 8063/8755C Operators Guide Contents About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents Projector features About contents of packagePreparations CB/PB CR/PR ProjectorControl buttons Remote controlSetting up Arrangement At 43 screenAt 169 screen Adjusting the projectors elevator About the filter cover for bottom-up use About Plug-and-Play capability Connecting your devicesConnecting to a monitor output Connecting to a speaker with amplifier outputExamples of connection with a computer Examples of connection with a VCR/DVD player CR/PRCB/PB Connecting power supply Putting batteries Remote controlUsing the remote control Turning on the power Power on/offTurning off the power PowerSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundAdjusting the zoom and focus Searching an input signal At a RGB signal Normal  43   At a video signal /no signal 43  169  SmallAdjusting the position Using the automatic adjustment feature At a RGB signal  At a video signalUsing the magnify feature Freezing the screenTemporarily blanking the screen Available function Remote control operation Operating the computer screenUSB mouse and keyboard control Using the menu function Multifunctional settingsEasy Menu Easy Menu Gamma Picture MenuHigh  Middle  LOW  Custom Picture MenuColor Temp SecamProgressive TV  Film  Turn OFFLOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1Image Menu PhaseOver Scan PositionAt a video signal Auto AdjustImage Menu SizeComponent  Scart RGB Input MenuAuto  Ntsc  PAL  Secam Video FormatInformation Input MenuVolume Setup MenuNormal  Whisper Normal  Hinvert  Vinvert  H&VINVERTMenu Position Screen MenuOSD Bright BlankStart UP Screen MenuMy Screen My Screen LockNo Input is Detected Sync is OUT of Range MessageOption Menu Reset  CancelSearch Auto OFFFactory Reset Service GhostOption Menu FAN SpeedLamp MaintenanceLamp Case of replacement by yourselfAir filter Apply a vacuum cleaner to the air filter and filter coverEnglish There is no input signal Internal portion temperature is risingRelated messages Message Description Related messagesRegarding the indicator lamps It is time to clean the air filter Regarding the indicator lampsCooling fan is not operating There is a possibility that the interior portionPower switch is not set to the on position Electrical power cord is not pluggedThese has not been properly fixed Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects RGB input Video input SpecificationRGB output Communication portSpecifications Page Example of computer signal Vesa TextVesa Initial set signals RGB in 1, B RGB in 2, C RGB OUT Connection to the portsComponent Video G Y, H CB/PB, I CR/PR CTS RTSConnecting the cable Communications settingRS-232C Communication Changing the projector settings Set command Requesting projector status Get commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Over Scan Frame Lock Menu Position H Lamp Time Page Audio Visual Products