Dukane 8063 Electrical power cord is not plugged, Power switch is not set to the on position

Page 58

Troubleshooting

Phenomena that may easily be mistaken for machine defects

WARNING ►Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet After making sure that the smoke or odor has stopped, contact your dealer or service company.

1. Before requesting repair, please check in accordance with the following chart. This operation sometimes resolves your problem.

If the situation cannot be corrected,

2. The projector’s microprocessor may need to be reset. Please push the Restart switch by using a cocktail stick or similar and the projector will restart.

3. Some setting may be wrong. Please use the FACTORY RESET function of SERVICE menu in the OPTION menu (37) to reset all settings to factory

default.

Then, if the problem is not removed after maintenance, please contact your dealer or service company.

Phenomenon

Cases not involving a machine defect

Reference

page

Power does not

come on.

The electrical power cord is not plugged in.

13

Correctly connect the power cord.

 

The power switch is not set to the on position.

16

Set the power switch to [ ] (On).

 

The main power source has been interrupted during

 

operation such as by a power outage (blackout), etc.

 

Please turn the power off, and allow the unit to cool down at

16

least 20 minutes. After the projector has sufficiently cooled

 

down, please turn the power on again.

 

Either there is no lamp and/or lamp cover, or either

 

of these has not been properly fixed.

 

Please turn the power off, and allow the unit to cool down at

38, 39

least 45 minutes. After the projector has sufficiently cooled

 

down, please make confirmation of the attachment state of

 

the lamp and lamp cover, and then turn the power on again.

 

46

Page 57 Page 59
Image 58
Page 57 Page 59
Contents LCD Projector Model 8063/8755C Operators Guide Contents About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page Thank you for purchasing this projector About this manualTrademark acknowledgment Contents About contents of package Projector featuresPreparations Projector CB/PB CR/PRRemote control Control buttonsSetting up At 43 screen ArrangementAt 169 screen Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityConnecting to a speaker with amplifier output Connecting to a monitor outputExamples of connection with a computer CR/PR Examples of connection with a VCR/DVD playerCB/PB Connecting power supply Remote control Putting batteriesUsing the remote control Turning off the power Power on/offTurning on the power PowerOperating Adjusting the volumeSelecting an input signal Temporarily muting the sound At a RGB signal Normal  43  Searching an input signalAdjusting the zoom and focus  At a video signal /no signal 43  169  Small At a RGB signal Using the automatic adjustment featureAdjusting the position  At a video signalFreezing the screen Using the magnify featureTemporarily blanking the screen Operating the computer screen Available function Remote control operationUSB mouse and keyboard control Multifunctional settings Using the menu functionEasy Menu Easy Menu Picture Menu GammaColor Temp Picture MenuHigh  Middle  LOW  Custom SecamLOAD1  LOAD2  LOAD3  LOAD4 TV  Film  Turn OFFProgressive SAVE4 SAVE3  SAVE2  SAVE1Over Scan PhaseImage Menu PositionImage Menu Auto AdjustAt a video signal SizeAuto  Ntsc  PAL  Secam Input MenuComponent  Scart RGB Video FormatInput Menu InformationNormal  Whisper Setup MenuVolume Normal  Hinvert  Vinvert  H&VINVERTOSD Bright Screen MenuMenu Position BlankMy Screen Screen MenuStart UP My Screen LockMessage No Input is Detected Sync is OUT of RangeSearch Reset  CancelOption Menu Auto OFFOption Menu Service GhostFactory Reset FAN SpeedMaintenance LampCase of replacement by yourself LampApply a vacuum cleaner to the air filter and filter cover Air filterEnglish Internal portion temperature is rising There is no input signalRelated messages Related messages Message DescriptionRegarding the indicator lamps Cooling fan is not operating Regarding the indicator lampsIt is time to clean the air filter There is a possibility that the interior portionThese has not been properly fixed Electrical power cord is not pluggedPower switch is not set to the on position Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects RGB output SpecificationRGB input Video input Communication portSpecifications Page Vesa Text Example of computer signalVesa Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTComponent Video G Y, H CB/PB, I CR/PR RTS CTSCommunications setting Connecting the cableRS-232C Communication Using the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Over Scan Frame Lock Menu Position H Lamp Time Page Audio Visual Products
Top Page Image Contents