Dukane 8063, 8755C user manual Connecting your devices, About Plug-and-Play capability

Page 22

Setting up

Connecting your devices

CAUTION ►Turn off all devices prior to connecting them to the projector. Attempting to connect a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction and/or damage to the device and/or projector.

►Use the accessory cable or a designated-type cable for the connection. Some cables have to be used with core set. A too long cable may cause a certain picture degradation. Please consult with your dealer for details. For cables that have a core only at one end, connect the core to the projector.

►Make sure that you connect devices to the correct port. Incorrect connection may result in malfunction and/or damage to the device and/or projector.

NOTE • Whenever attempting to connect a laptop computer to the projector, be sure to activate the laptop’s RGB external image output (set the laptop to CRT display or to simultaneous LCD and CRT display). For details on how this is done, please refer to the instruction manual of the corresponding laptop computer.

•Secure the screws on the connectors and tighten.

•Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector.

•For some RGB signal modes, the optional Mac adapter is necessary.

•When the image resolution is changed on a computer, depending on an input, automatic adjust function may take some time and may not be completed. In this case, you may not be able to see a check box to select “Yes/No” for the new resolution on Windows. Then the resolution will go back to the original. It might be recommended to use other CRT or LCD monitors to change the resolution.

About Plug-and-Play capability

Plug-and-Play is a system composed of the computer, its operating system and peripheral equipment (i.e. display devices). This projector is compatible with VESA DDC 2B. Plug-and-Play can be achieved by connecting this projector to computers that are VESA DDC (display data channel) compatible.

•Please take advantage of this function by connecting the accessory RGB cable to the RGB IN1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

•Please use the standard drivers in your computer as this projector is a Plug-and-Play monitor.

10

Image 22

Contents LCD Projector Model 8063/8755C Operators Guide Contents About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page Thank you for purchasing this projector About this manualTrademark acknowledgment Contents About contents of package Projector featuresPreparations Projector CB/PB CR/PRRemote control Control buttonsSetting up At 43 screen ArrangementAt 169 screen Adjusting the projectors elevator About the ﬁlter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityConnecting to a speaker with ampliﬁer output Connecting to a monitor outputExamples of connection with a computer CR/PR Examples of connection with a VCR/DVD playerCB/PB Connecting power supply Remote control Putting batteriesUsing the remote control Turning off the power Power on/offTurning on the power PowerOperating Adjusting the volumeSelecting an input signal Temporarily muting the sound At a RGB signal Normal  43  Searching an input signalAdjusting the zoom and focus  At a video signal /no signal 43  169  Small At a RGB signal Using the automatic adjustment featureAdjusting the position  At a video signalFreezing the screen Using the magnify featureTemporarily blanking the screen Operating the computer screen Available function Remote control operationUSB mouse and keyboard control Multifunctional settings Using the menu functionEasy Menu Easy Menu Picture Menu GammaColor Temp Picture MenuHigh  Middle  LOW  Custom SecamLOAD1  LOAD2  LOAD3  LOAD4 TV  Film  Turn OFFProgressive SAVE4 SAVE3  SAVE2  SAVE1Over Scan PhaseImage Menu PositionImage Menu Auto AdjustAt a video signal SizeAuto  Ntsc  PAL  Secam Input MenuComponent  Scart RGB Video FormatInput Menu InformationNormal  Whisper Setup MenuVolume Normal  Hinvert  Vinvert  H&VINVERTOSD Bright Screen MenuMenu Position BlankMy Screen Screen MenuStart UP My Screen LockMessage No Input is Detected Sync is OUT of RangeSearch Reset  CancelOption Menu Auto OFFOption Menu Service GhostFactory Reset FAN SpeedMaintenance LampCase of replacement by yourself LampApply a vacuum cleaner to the air ﬁlter and ﬁlter cover Air ﬁlterEnglish Internal portion temperature is rising There is no input signalRelated messages Related messages Message DescriptionRegarding the indicator lamps Cooling fan is not operating Regarding the indicator lampsIt is time to clean the air ﬁlter There is a possibility that the interior portionThese has not been properly ﬁxed Electrical power cord is not pluggedPower switch is not set to the on position Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects RGB output SpeciﬁcationRGB input Video input Communication portSpeciﬁcations Page Vesa Text Example of computer signalVesa Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTComponent Video G Y, H CB/PB, I CR/PR RTS CTSCommunications setting Connecting the cableRS-232C Communication Using the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Over Scan Frame Lock Menu Position H Lamp Time Page Audio Visual Products