Dukane 8755C, 8063 user manual Lamp, Case of replacement by yourself

Page 51

Lamp cover

1.

2.

Maintenance

Lamp (continued)

When the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible.

Turn the projector off, and unplug the power cord. Allow the lamp to cool for at least 45 minutes.

To prepare a new lamp, contact your dealer and tell the lamp type number = 456-8063.If the projector is mounted on the ceiling, or if the lamp has

broken, also ask the dealer to replace the lamp.

ENGLISH

In the case of replacement by yourself,

3. After making sure that the projector has cooled adequately, slowly turn over the projector, so that the bottom is facing up.

4. Please unhook the claws of the lamp cover using a minus screwdriver or similar, and

remove the lamp cover.

5. Loosen the 2 screws (marked by arrow) of the lamp, and slowly pick up the lamp by the

handles.

6. Insert the new lamp, and retighten ﬁrmly two screws that are loosened in the previous

process to lock it in place.

7. Interlocking the 2 tabs of the lamp cover to the projector, position the lamp cover on the

projector. Then push the center point of two claws to ﬁx the lamp cover.

8. Slowly turn the projector so that the top is facing up.

9. Turn the projector on, and reset the lamp time using the LAMP TIME function of OPTION

menu (36).

Claws

Screws marked

by arrow

Tabs

Center point of claws

Claws

NOTE • When the lamp has been replaced after the message of "THE POWER WILL TURN OFF AFTER 0hr." is displayed, complete the following operation within 10 minutes of switching power on.

•Incorrectly resetting of the lamp timer (resetting without replacement, or neglect of resetting after replacement) will result in incorrect message functions.

39

Image 51

Contents LCD Projector Model 8063/8755C Operators Guide Contents About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents Projector features About contents of packagePreparations CB/PB CR/PR ProjectorControl buttons Remote controlSetting up Arrangement At 43 screenAt 169 screen Adjusting the projectors elevator About the ﬁlter cover for bottom-up use About Plug-and-Play capability Connecting your devicesConnecting to a monitor output Connecting to a speaker with ampliﬁer outputExamples of connection with a computer Examples of connection with a VCR/DVD player CR/PRCB/PB Connecting power supply Putting batteries Remote controlUsing the remote control Power Power on/offTurning on the power Turning off the powerTemporarily muting the sound Adjusting the volumeSelecting an input signal Operating At a video signal /no signal 43  169  Small Searching an input signalAdjusting the zoom and focus  At a RGB signal Normal  43  At a video signal Using the automatic adjustment featureAdjusting the position  At a RGB signalUsing the magnify feature Freezing the screenTemporarily blanking the screen Available function Remote control operation Operating the computer screenUSB mouse and keyboard control Using the menu function Multifunctional settingsEasy Menu Easy Menu Gamma Picture MenuSecam Picture MenuHigh  Middle  LOW  Custom Color TempSAVE4 SAVE3  SAVE2  SAVE1 TV  Film  Turn OFFProgressive LOAD1  LOAD2  LOAD3  LOAD4Position PhaseImage Menu Over ScanSize Auto AdjustAt a video signal Image MenuVideo Format Input MenuComponent  Scart RGB Auto  Ntsc  PAL  SecamInformation Input MenuNormal  Hinvert  Vinvert  H&VINVERT Setup MenuVolume Normal  WhisperBlank Screen MenuMenu Position OSD BrightMy Screen Lock Screen MenuStart UP My ScreenNo Input is Detected Sync is OUT of Range MessageAuto OFF Reset  CancelOption Menu SearchFAN Speed Service GhostFactory Reset Option MenuLamp MaintenanceLamp Case of replacement by yourselfAir ﬁlter Apply a vacuum cleaner to the air ﬁlter and ﬁlter coverEnglish There is no input signal Internal portion temperature is risingRelated messages Message Description Related messagesRegarding the indicator lamps There is a possibility that the interior portion Regarding the indicator lampsIt is time to clean the air ﬁlter Cooling fan is not operatingPhenomenon Cases not involving a machine defect Reference Electrical power cord is not pluggedPower switch is not set to the on position These has not been properly ﬁxedPhenomena that may easily be mistaken for machine defects Communication port SpeciﬁcationRGB input Video input RGB outputSpeciﬁcations Page Example of computer signal Vesa TextVesa Initial set signals RGB in 1, B RGB in 2, C RGB OUT Connection to the portsComponent Video G Y, H CB/PB, I CR/PR CTS RTSConnecting the cable Communications settingRS-232C Communication Increasing the projector setting value Increment command Requesting projector status Get commandChanging the projector settings Set command Using the projector default settings Reset CommandCRC Be EF FB FA Color Temp Gain G Over Scan Frame Lock Menu Position H Lamp Time Page Audio Visual Products