Dukane 8063, 8755C user manual Image Menu, Over Scan, Position, Phase

Page 40

Multifunctional settings

IMAGE Menu

With the IMAGE menu, items shown in the table below can be performed.

Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress. Then perform it referring to the following table.

MENU [RGB]

 

:SELECT

PICTURE

ASPECT

4:3

IMAGE

OVER SCAN

95

INPUT

V POSITION

25

SETUP

H POSITION

142

SCREEN

H PHASE

16

OPTION

H SIZE

1344

EASY MENU

AUTO ADJUST

 

Item

Description

 

Using the buttons ▲/▼ switches the mode for aspect ratio.

 

At a RGB signal

 

4:3 16:9 NORMAL

 

At a video signal / no signal

ASPECT

4:3 16:9 SMALL

 

 

• The NORMAL mode keeps the original aspect ratio of the signal.

 

• At a HDTV signal of 1125i (1080i) or 750p (720p) of COMPONENT

 

VIDEO input, this item can't be selected.

 

• Performing the automatic adjustment initializes the aspect ratio

 

setting.

 

Using the buttons ▲/▼ adjusts the over-scan ratio.

OVER SCAN

Large (It reduces picture) Small (It magnifies picture)

• This item can be selected only at a video signal.

 

• When this adjustment is too large, certain degradation may appear

 

at the frame area of the picture. In such a case, please adjust small.

V POSITION

Using the buttons ▲/▼ adjusts the vertical position.

Up Down

 

H POSITION

Using the buttons ▲/▼ adjusts the horizontal position.

Left Right

 

 

Using the buttons ▲/▼ adjusts the horizontal phase to eliminate

 

flicker.

H PHASE

Right Left

 

• This item can be selected only at a RGB signal or a component

 

video signal.

28

Image 40
Contents LCD Projector Model 8063/8755C Operators Guide Contents About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page Thank you for purchasing this projector About this manualTrademark acknowledgment Contents About contents of package Projector featuresPreparations Projector CB/PB CR/PRRemote control Control buttonsSetting up At 43 screen ArrangementAt 169 screen Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityConnecting to a speaker with amplifier output Connecting to a monitor outputExamples of connection with a computer CR/PR Examples of connection with a VCR/DVD playerCB/PB Connecting power supply Remote control Putting batteriesUsing the remote control Power on/off Turning on the powerTurning off the power PowerAdjusting the volume Selecting an input signalOperating Temporarily muting the soundSearching an input signal Adjusting the zoom and focus At a RGB signal Normal  43   At a video signal /no signal 43  169  SmallUsing the automatic adjustment feature Adjusting the position At a RGB signal  At a video signalFreezing the screen Using the magnify featureTemporarily blanking the screen Operating the computer screen Available function Remote control operationUSB mouse and keyboard control Multifunctional settings Using the menu functionEasy Menu Easy Menu Picture Menu GammaPicture Menu High  Middle  LOW  CustomColor Temp SecamTV  Film  Turn OFF ProgressiveLOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1Phase Image MenuOver Scan PositionAuto Adjust At a video signalImage Menu SizeInput Menu Component  Scart RGBAuto  Ntsc  PAL  Secam Video FormatInput Menu InformationSetup Menu VolumeNormal  Whisper Normal  Hinvert  Vinvert  H&VINVERTScreen Menu Menu PositionOSD Bright BlankScreen Menu Start UPMy Screen My Screen LockMessage No Input is Detected Sync is OUT of RangeReset  Cancel Option MenuSearch Auto OFFService Ghost Factory ResetOption Menu FAN SpeedMaintenance LampCase of replacement by yourself LampApply a vacuum cleaner to the air filter and filter cover Air filterEnglish Internal portion temperature is rising There is no input signalRelated messages Related messages Message DescriptionRegarding the indicator lamps Regarding the indicator lamps It is time to clean the air filterCooling fan is not operating There is a possibility that the interior portionElectrical power cord is not plugged Power switch is not set to the on positionThese has not been properly fixed Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects Specification RGB input Video inputRGB output Communication portSpecifications Page Vesa Text Example of computer signalVesa Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTComponent Video G Y, H CB/PB, I CR/PR RTS CTSCommunications setting Connecting the cableRS-232C Communication Requesting projector status Get command Changing the projector settings Set commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Over Scan Frame Lock Menu Position H Lamp Time Page Audio Visual Products