Dukane 8063, 8755C user manual Power on/off, Turning on the power, Turning off the power

Page 28
1.
2.

Power on/off

Power on/off

WARNING ►When the power is on, a strong light is emitted. Do not look into the lens or vents of the projector.

NOTE • Turn the power on/off in right order. Please power on the projector before the connected devices. Power off the projector after the connected devices.

 

 

 

STANDBY/ON

VIDEO

RGB

SEARCH

 

ASPECT

 

AUTO

BLANK

MAGNIFY

HOME

PAGE UP

VOLUME

ON

 

 

 

 

END

PAGE DOWN

MUTE

OFF

 

 

 

FREEZE

 

 

KEYSTONE

POSITION

 

 

MENU

 

ENTER

 

ESC

 

 

RESET

STANDBY/ON button

 

LAMP

 

 

 

TEMP

 

POWER

 

POWER

 

 

 

indicator

STANDBY/ON

 

INPUT

 

 

 

MENU

 

 

 

 

 

Power switch

Turning on the power

Make sure that the power cord is firmly and correctly connected to the projector and outlet.

Open the lens cover, and set the power switch to the ON position.

The power indicator will light to solid orange. Then wait several seconds because buttons may not function for these several seconds.

POWER (Solid orange) POWER (Blinking green)

POWER (Solid green)

3. Press the STANDBY/ON button on the projector or remote control.

The projector lamp will light up and the POWER indicator will begin blinking green. When the power is completely on, the indicator will stop blinking light green.

To display the picture, select an input signal according to the section "Selecting an input signal" (17).

Turning off the power

1. Press the STANDBY/ON button on the projector or remote control.

The message "Power off?" will appear on the screen for approximately 5 seconds.

2. Press the STANDBY/ON button on the projector or remote control again while the message is visible.

The projector lamp will go off, and the POWER indicator will begin blinking orange.

Then the POWER indicator will stop blinking and light to solid orange when the lamp cooling is complete.

Power off?

POWER (Blinking orange)

POWER (Solid orange)

3. Make sure that the power indicator lights to solid orange, set the power switch to the OFF position. The POWER indicator will go off. Close the lens cover.

16

Image 28
Contents LCD Projector Model 8063/8755C Operators Guide Contents About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page Thank you for purchasing this projector About this manualTrademark acknowledgment Contents About contents of package Projector featuresPreparations Projector CB/PB CR/PRRemote control Control buttonsSetting up At 43 screen ArrangementAt 169 screen Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityConnecting to a speaker with amplifier output Connecting to a monitor outputExamples of connection with a computer CR/PR Examples of connection with a VCR/DVD playerCB/PB Connecting power supply Remote control Putting batteriesUsing the remote control Power on/off Turning on the powerTurning off the power PowerAdjusting the volume Selecting an input signalOperating Temporarily muting the soundSearching an input signal Adjusting the zoom and focus At a RGB signal Normal  43   At a video signal /no signal 43  169  SmallUsing the automatic adjustment feature Adjusting the position At a RGB signal  At a video signalFreezing the screen Using the magnify featureTemporarily blanking the screen Operating the computer screen Available function Remote control operationUSB mouse and keyboard control Multifunctional settings Using the menu functionEasy Menu Easy Menu Picture Menu GammaPicture Menu High  Middle  LOW  CustomColor Temp SecamTV  Film  Turn OFF ProgressiveLOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1Phase Image MenuOver Scan PositionAuto Adjust At a video signalImage Menu SizeInput Menu Component  Scart RGBAuto  Ntsc  PAL  Secam Video FormatInput Menu InformationSetup Menu VolumeNormal  Whisper Normal  Hinvert  Vinvert  H&VINVERTScreen Menu Menu PositionOSD Bright BlankScreen Menu Start UPMy Screen My Screen LockMessage No Input is Detected Sync is OUT of RangeReset  Cancel Option MenuSearch Auto OFFService Ghost Factory ResetOption Menu FAN SpeedMaintenance LampCase of replacement by yourself LampApply a vacuum cleaner to the air filter and filter cover Air filterEnglish Internal portion temperature is rising There is no input signalRelated messages Related messages Message DescriptionRegarding the indicator lamps Regarding the indicator lamps It is time to clean the air filterCooling fan is not operating There is a possibility that the interior portionElectrical power cord is not plugged Power switch is not set to the on positionThese has not been properly fixed Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects Specification RGB input Video inputRGB output Communication portSpecifications Page Vesa Text Example of computer signalVesa Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTComponent Video G Y, H CB/PB, I CR/PR RTS CTSCommunications setting Connecting the cableRS-232C Communication Requesting projector status Get command Changing the projector settings Set commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Over Scan Frame Lock Menu Position H Lamp Time Page Audio Visual Products