AVE MV DR4000 manual System Information and channel selection, 09- 05-2003

Page 14

3.3 System Information and channel selection

3.3.1SYSTEM INFORMATION

You can display system settings information as shown on Figure 3.3 A below at any time by pressing the Display button . In the playback mode, the recorded video information is displayed. In the live or recording mode, the Manual Recording information is displayed. Each sequential press of the Display button displays a different message detailed in the following example. By default, the unit displays titles, time, and date on a monitor as shown next.

Default display

CH 1

CH 2

CH 3

CH 4

09- 05-2003 16:13:02

CH1 , CH2, CH3, CH4 are titles for each channel, changeable in Setup menu

Capacity Status :

09- 05-2003 16:13:02

( System Data/ Time )

Press the Display button once; the DVR will display the following sample message plus the default display. Press the Display button again; the unit will not display any OSD message. Press the button one more time to back to the default display.

12

Image 14

Contents AVE Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Features Product IntroductionHard disk compartment lock Front ViewHard-disk drive compartment Display button Rec IndicatorDisk Indicator Up / Down CH2 / CH1 buttonsMobile Rack HDD LED Mobile Rack Power LEDJog Dial Rear View Between 75Ω and Hi-Z Record in Input This pin Alarm In/Out This Figure is Looked from the Rear View Attaching AN External Device to DVR Connecting with 1 to 4 CamerasBasic Connection Maxtor Hard-Disk Drive InstallationSeagate System Information System Information and channel selection09- 05-2003 Quality Best Ntsc Rate 6 HR Size POSUpdating System Software Ntsc Audio on Configuring Recording SettingsNtsc Audio OFF PAL Audio OFFPAL Audio on Manual Recording Timer RecordingRecording Operations Start END 0000-0000 M 0000-0000 W 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000Alarm / Motion ALM Operation REC Rate Alarm / Motion RecordingPRE- Alarm OFF Motion Setting Main Alarm REC Enable REC Quality Best Audio OFF ALM Type ALM DurationExternally triggered Recording BelowFast Forward/Reverse Operation Status From REC mode to Playback modePlayback Operations Search to play back a particular recorded videoPlay Back Recorded Video from a HDD of the mobile rack Slow Forward/ ReversePlayback Picture-by-picture Full List Search Search Full List Alarm List Time Search Thumbnail SD CardSearch Operations Alarm list Search Time SearchMM DD Year 03 / 13 Thumbnail SearchSD Card Search Set HD 2 to Backup first. Take the following steps Backup OperationsMobile Rack HD Backup Operations F0000.JPG F0001.JPG F0002.JPG F0003.JPG F0004.JPG F0005.JPGFull Select Duplicate a particular recorded video from HD1 to HD2Save to F0000.JPG Save to F0001.JPG Save to F000N.JPG Security Digital Card SD Card Backup OperationsDisk Setting Reformat HD2 Usage Transfer the system setting info of DVR to another For more detail Backup the System setting info into SD CardSave the whole setting into the SD card Archive video of AVI Clips into SD CardKey Lock Operation Set Up Menu Navigation Buttons Setup button Enter buttonREC Setting REC QualityAlarm / Motion Setting ALM Type PRE- Alarm 0600-1800 0000-0000 REC Schedule0600-1600 1200-1800 Channel 1 2 3 Dwell 03 03 03 03 TitleNET Enable OFF NET Dhcp NET IP SET FTP Setting Main NET Enable1 S Http Port FTP SettingComm Setting Comm ID Account SET Main SET FTP on / OFFUser AccountFTP Account FTP IP PathBackup HD HD2 Usage HD 1System Situation MAC 00 0c 0c 00 00 Bios Date Mar 10 Communication Protocol SetupGeneral Command Format Request Time Second Category=0x02 Value of a specific front panel keyDEC HEX Set Time Second Category=0x02DVR Playback Error REC ModeNon REC Mode Request State Second Category=0x06Jumper settings of hard-disk drives for the system Location Built-in hard diskMobile Rack HDD Installation Page Page System Default Disk Setting Reformat SET RS232 / RS485D. Message Meanings Network Viewer PIN noInstall the Network Viewer for the ZIP file View the 4CH DVR video from a remote PC Page Function Buttons Description Page Set the Alarm record settings Change the Record & Timer Properties Via the NetworkSet the regular record settings Set the Record ScheduleArchive Images to the Computer Image Viewer 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03 Point stops recording Previously recorded data remainingConnect to a computer Physical specification of RJ-45 cable for EthernetCable Connections Connect to a LAN Hub IntranetEnable DVR Network Function RJ-45 PIN configuration for LAN HubConfigure Your DVR Network Settings Connect to WAN InternetEnable Dhcp Function Set IP AddressPage 12.3 TCP/IP Communication Software 12.4 TCP/IP installation 12.5 TCP/IP Configuration setting Click Start Settings Control Panel NetworkConnection Testing Click Start ProgramsPage Connecting the 4CH DVR Description of functional keysBrowsing images from the 4CH DVR Page Change Record / Alarm Setting Change Timer Record Setting Change Pan/Tilt/Zoom Setting Page Design and specifications subject to change without notice Model Number MV-DR4000Appendix 1. -SCANIP