AVE MV DR4000 Built-in hard disk, Jumper settings of hard-disk drives for the system Location

Page 51

7. IDE Hard Disk Installation

Usually, the unit comes with one hard-disk drive installed in compartment HD 1, which is default-configured as a master. The jumper settings configuration of the installed hard-disk drives for the unit and compatible drives which can be used with this unit are listed in the table below. To install two hard disk drives in compartment HD 1 and HD 2, please take the following steps.

The jumper settings of hard-disk drives for the system

 

Location

Jumper

IDE 1

Compartment HD 1

Master

IDE 2

Compartment HD 2

Master

 

 

 

7.1 Built-in hard disk

1.

1. Unscrew all the mounting screws on the mobile rack of the unit and detach it.

2.3.

2. Carefully lift the mobile rack to a vertical position.

3. Unscrew the secured screws to detach the hard disk rack.

4.

5.

4.

Setting the jumper of your hard disk

 

 

 

 

 

driver. The way to set the jumper of the

 

 

 

drive varies between manufacturers;

 

 

 

please refer to the instructions on the

 

 

 

driver to set the jumpers in the master

 

 

 

position.

 

 

5.

Place the hard disk in the rack.

 

 

 

 

49

Image 51
Contents AVE Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Introduction Product FeaturesFront View Hard-disk drive compartmentHard disk compartment lock Up / Down CH2 / CH1 buttons Rec IndicatorDisk Indicator Display buttonMobile Rack Power LED Jog DialMobile Rack HDD LED Between 75Ω and Hi-Z Rear ViewAlarm In/Out This Figure is Looked from the Rear ViewRecord in Input This pin Connecting with 1 to 4 Cameras Basic ConnectionAttaching AN External Device to DVR Hard-Disk Drive Installation SeagateMaxtor System Information and channel selection 09- 05-2003System Information Size POS Quality Best Ntsc Rate 6 HRUpdating System Software PAL Audio OFF Configuring Recording SettingsNtsc Audio OFF Ntsc Audio onPAL Audio on Timer Recording Recording OperationsManual Recording Start END 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 M 0000-0000 WREC Quality Best Audio OFF ALM Type ALM Duration Alarm / Motion RecordingPRE- Alarm OFF Motion Setting Main Alarm REC Enable Alarm / Motion ALM Operation REC RateBelow Externally triggered RecordingSearch to play back a particular recorded video Operation Status From REC mode to Playback modePlayback Operations Fast Forward/ReverseSlow Forward/ Reverse Playback Picture-by-picturePlay Back Recorded Video from a HDD of the mobile rack Search Full List Alarm List Time Search Thumbnail SD Card Search OperationsFull List Search Time Search Alarm list SearchThumbnail Search SD Card SearchMM DD Year 03 / 13 F0000.JPG F0001.JPG F0002.JPG F0003.JPG F0004.JPG F0005.JPG Backup OperationsMobile Rack HD Backup Operations Set HD 2 to Backup first. Take the following stepsSelect Duplicate a particular recorded video from HD1 to HD2 FullSecurity Digital Card SD Card Backup Operations Disk Setting Reformat HD2 UsageSave to F0000.JPG Save to F0001.JPG Save to F000N.JPG Archive video of AVI Clips into SD Card For more detail Backup the System setting info into SD CardSave the whole setting into the SD card Transfer the system setting info of DVR to anotherKey Lock Operation Enter button Set Up Menu Navigation Buttons Setup buttonREC Quality REC SettingAlarm / Motion Setting ALM Type PRE- Alarm REC Schedule 0600-1600 1200-18000600-1800 0000-0000 Title Channel 1 2 3 Dwell 03 03 03 03NET Enable NET Enable OFF NET Dhcp NET IP SET FTP Setting MainAccount SET Main SET FTP on / OFF Http Port FTP SettingComm Setting Comm ID 1 SPath AccountFTP Account FTP IP UserHD 1 Backup HD HD2 UsageSystem Situation MAC 00 0c 0c 00 00 Bios Date Mar 10 Setup General Command FormatCommunication Protocol Set Time Second Category=0x02 Value of a specific front panel keyDEC HEX Request Time Second Category=0x02Request State Second Category=0x06 REC ModeNon REC Mode DVR Playback ErrorBuilt-in hard disk Jumper settings of hard-disk drives for the system LocationMobile Rack HDD Installation Page Page System Default SET RS232 / RS485 Disk Setting ReformatD. Message Meanings PIN no Network ViewerInstall the Network Viewer for the ZIP file View the 4CH DVR video from a remote PC Page Function Buttons Description Page Set the Record Schedule Change the Record & Timer Properties Via the NetworkSet the regular record settings Set the Alarm record settingsArchive Images to the Computer Image Viewer Point stops recording Previously recorded data remaining 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03Connect to a LAN Hub Intranet Physical specification of RJ-45 cable for EthernetCable Connections Connect to a computerConnect to WAN Internet RJ-45 PIN configuration for LAN HubConfigure Your DVR Network Settings Enable DVR Network FunctionSet IP Address Enable Dhcp FunctionPage 12.3 TCP/IP Communication Software 12.4 TCP/IP installation Click Start Settings Control Panel Network 12.5 TCP/IP Configuration settingClick Start Programs Connection TestingPage Description of functional keys Connecting the 4CH DVRBrowsing images from the 4CH DVR Page Change Record / Alarm Setting Change Timer Record Setting Change Pan/Tilt/Zoom Setting Page Model Number MV-DR4000 Design and specifications subject to change without noticeAppendix 1. -SCANIP